The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old June 19, 2011, 06:45 PM   #1
Bill Daniel
Senior Member
 
Join Date: February 10, 2000
Location: Bowling Green, KY.
Posts: 376
Measurements are they exact or averages

I have a Savage FCP in 308 and have been searching for the perfect target load. I have started with SMK 168 HPBTs and found 44 grains of Varget to give me my best groups so I am now trying to tinker with seating distance off the lands. I have a Hornady LNL Classic single stage press and use a Redding competition seating die. My brass is trimmed to 2.05" and is fire formed Lapua. I use a Hornady comparitor and a Dillon dial caliper (which I just noticed was made in China). Having said that with no change to the set up my lengths to the ogive on the bullet will vary 0.001" to 0.002". When people report that their load is 0.01 or 0.005 off the lands is that absolute or an average of a certain number of cartriges.
Thanks, Bill Daniel
__________________
Prosecute criminals to the fullest extent of the law and their weapons will become harmless.

"Let us speak courteously, deal fairly, and keep ourselves armed and ready." Theodore Roosevelt 1903
Bill Daniel is offline  
Old June 19, 2011, 07:43 PM   #2
TXGunNut
Senior Member
 
Join Date: January 16, 2010
Location: If you have to ask...
Posts: 2,851
IMHO it's a tolerable range. They won't be exact because of slight variations in components and loading processes. An average could have measurements outside of a tolerable range. When I measure headspace I know it's not an exact number, more of a benchmark or starting place. Seating a bullet .01-.005" off the lands isn't always the best strategy, BTW. Sometimes it works, sometimes it doesn't.
__________________
Life Member NRA, TSRA
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call Lonesome Dove
My favorite recipes start out with a handful of used wheelweights.
TXGunNut is offline  
Old June 19, 2011, 08:00 PM   #3
Jim243
Senior Member
 
Join Date: January 5, 2009
Posts: 4,335
For me it is an absolute. I use a Hornady L-N-L case length gauge and cartrage for measurement for each new bullet brand and type and weight.

That gives me the MAX OAL for that bullet "IN MY RIFLE". It would be different in YOUR rifle. From that OAL I back off 0.050 inches and that is the OAL that will place the bullet 0.050 off the lands.

Simple.
Jim
__________________
Si vis pacem, para bellum
Jim243 is offline  
Old June 19, 2011, 09:35 PM   #4
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,187
Bill,

General consensus seems to be that few guns can show a difference of less than a hundredth of an inch. People seeking the best seating depth usually tune in 0.010" steps for than reason, then discover they actually have a range of 0.020" to 0.030" of the lands that's best and aim for the middle of that range. No telling where it will be. A lot of people just assume it will be close to the throat because that's typically better than standard seating depth, but it doesn't always work out. Berger has shown it's VLD's like to be as much as 0.165" off the lands for best accuracy, so be prepared to go from near the throat all the way to full seating short of the ogive starting to vanish into the case mouth.

Because pressures vary with seating depth, knock your load down to 40 grains before you do this. Find what works best with that load, then work the charge back up to tighten the groups to best performance from there.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Patron Member
Unclenick is offline  
Old June 19, 2011, 10:20 PM   #5
cracked butt
Senior Member
 
Join Date: December 22, 2001
Location: southeastern wisconsin
Posts: 537
edit: oops nevermind, I see that OP was using a oal tool to measure off ogive....
cracked butt is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:16 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06623 seconds with 9 queries