The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old June 7, 2008, 07:49 PM   #1
HondaCowboy82
Member
 
Join Date: November 20, 2005
Posts: 73
240 Gibbs / 6mm Gibbs Ammo?

Ran across a 1903 custom chambered for the 240 Gibbs. Anybody got a source for ammo or anybody willing to reload a few boxes for me for a price?
HondaCowboy82 is offline  
Old June 7, 2008, 08:11 PM   #2
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,476
I replied to your post in the Art of the Rifle forum. It's not just a matter of relaoding a few cases. The 240 Gibbs is a wildcat cartridge. You need dies and the gun in order to make ammo.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old June 8, 2008, 09:45 AM   #3
oldscot3
Senior Member
 
Join Date: July 1, 2007
Location: texas
Posts: 311
I had a 6.5 Gibbs once upon a time, and reloading for a Gibbs is a process that requires a few extra steps that involve having the weapon on hand. For instance, with my 6.5 Gibbs, you began with unfired 270 brass, necked it down to 264 so the bolt would just close on the case, then loaded it and fireformed the case to the chamber. That fireforming blew the case out to minimum taper and also moved the shoulder forward. At that point you reloaded for the Gibbs with its increased capacity.

I doubt if anyone familiar with various wildcats would endorse the idea of having someone else load for your weapon without having it on hand as a potentially dangerous situation could arise.
oldscot3 is offline  
Old June 9, 2008, 07:02 PM   #4
wncchester
Senior Member
 
Join Date: December 1, 2002
Posts: 2,832
Wildcat dies are hard to find and expensive to buy. The .240 Gibbs is basically the same cartridge as the Weatherby .240 Magnum and both show advantage over a .243 only with bullets of 100 grains or more. Unless you specifically a .240 Gibbs I think you would do better by getting the more conventional Magnum.
wncchester is offline  
Old July 31, 2008, 06:16 PM   #5
GregL
Junior Member
 
Join Date: July 31, 2008
Location: Lake Co. , Ca.
Posts: 2
Re: 240 Gibbs...

I have about 50 rounds of loaded ammo and a set of RCBS dies. They came in several boxes from an estate. You can have them for the shipping charge.
GregL
GregL is offline  
Old July 31, 2008, 08:10 PM   #6
Shoney
Senior Member
 
Join Date: February 21, 2002
Location: Transplanted from Montana
Posts: 2,311
The 240 Gibbs is a derivative of the 30-06 case. Brass can be formed from the 30-06 case by using case forming dies:
http://www.huntingtons.com/dies_caseform.html
__________________
I pledge allegiance to the Flag - - -, and to the Republic for which it stands….Our Forefathers were brilliant for giving us a Republic, not a democracy! Do you know the difference??? and WHY?http://www.wallbuilders.com/LIBissue...les.asp?id=111
Shoney is offline  
Old June 18, 2011, 07:09 AM   #7
booda
Junior Member
 
Join Date: June 18, 2011
Posts: 1
GregL,

Do you still have the 50 rounds and dies for the 240 gibbs??? Just picked one up.
booda is offline  
Old June 18, 2011, 08:32 AM   #8
JerryM
Senior Member
 
Join Date: April 4, 1999
Location: New Mexico
Posts: 1,884
I once chronographed a .30 Gibbs. It showed hot 30-06 velocities. I don't remember what his load was.
Many of those wildcatters used very long barrels and very high pressure loads to get advertised velocities.

I would be very interested in learning what your experience is with the 240 Gibbs. Please work up some loads, chronograph them, and let us know.

My own Pre 64 M70 .243 is a "fast" rifle. I have chronographed 100gr bullets over 3200 fps. Pressures had to be high, but no hard bolt lift or signs of excessive pressures. My working load is 45 gr 4350 with vel of 3150fps, and from the 22 in barrel.
That load was a recommended load when the .243 first came out, but current handbooks do not approach that. Evidently in some guns it is too hot. So as always begin with the recommended handbook starting loads and work up carefully.

I doubt that the .240 Gibbs will get much over 3200 fps with a 100 gr bullet unless the barrel is at least 26 -28 inches in length.
That is a reason I reload for all my guns.

Regards,
Jerry
__________________
Ecclesiastes 12:13 *¶Let us hear the conclusion of the whole matter: Fear God, and keep his commandments: for this is the whole duty of man.
14 *For God shall bring every work into judgment, with every secret thing, whether it be good, or whether it be evil.
JerryM is offline  
Old June 18, 2011, 12:10 PM   #9
brickeyee
Senior Member
 
Join Date: December 29, 2004
Posts: 3,342
Quote:
anybody willing to reload a few boxes for me for a price?
Seriously illegal without an 06 FFL.

You cannot sell reloads.
brickeyee is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:51 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08941 seconds with 9 queries