The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old June 16, 2011, 11:27 PM   #1
raluttrell
Junior Member
 
Join Date: June 16, 2011
Posts: 1
H 335 for my M1

Has anyone ever used Hodgon H 335 for reloads for the M1, it seeme like everone likes IMR 4895. I'm using 150 gr. FMJ/BT Hornady and 50gr. of H 335 Just looking for some feedback on this powder. It works great in my 5.56 and 7.62X51.
raluttrell is offline  
Old June 17, 2011, 12:39 AM   #2
dmazur
Senior Member
 
Join Date: July 5, 2007
Location: Pacific NW
Posts: 1,309
Well, there's this link -

John R. Clarke Article

Somewhere in the middle of the article, the author says, "There are other powders, for example Hodgdon's BL-C(2) and H-335, that will give performance about like that of Win. 748 Ball."

The table above (for 150gr bullets) shows loads of 49-50gr of Win 748.

My experience is with Varget, so I can't personally endorse H-335...but the above (often referenced) article seems to indicate that it has been used in the Garand.
__________________
.30-06 Springfield: 100 yrs + and still going strong
dmazur is offline  
Old June 17, 2011, 08:21 AM   #3
BombthePeasants
Senior Member
 
Join Date: November 17, 2008
Location: Texas
Posts: 335
to better address your concerns, may I suggest you join and/or visit the CMP forums, therein lies a sub-forum about reloading.

http://forums.thecmp.org/forumdisplay.php?f=94

As for me, I'm an ardent user of IMR 4064.
BombthePeasants is offline  
Old June 17, 2011, 09:38 AM   #4
Cruz5350
Member
 
Join Date: October 28, 2010
Posts: 63
I also want to reload for my M1, but was thinking of using Varget since I have a bunch for my .223. Any other Varget M1 users care to chime in on experience?

Thanks
Cruz5350 is offline  
Old June 17, 2011, 11:40 AM   #5
dmazur
Senior Member
 
Join Date: July 5, 2007
Location: Pacific NW
Posts: 1,309
I use 46.0gr of Varget with Hornady 150gr FMJBT and Winchester brass.

I have a McCann adjustable gas cylinder lock screw (gas nut) with one of the intermediate orifices installed and this seems to cycle reliably without any receiver heel battering.

I've read that it is possible to use Varget without the adj. gas nut, but I use it anyway because I've also read that a SEI brake will increase pressures slightly.

If you're reloading for competition, there may be problems with adjustable gas nuts and brakes are definitely not approved.

I use 49.0gr of Varget with 150gr bullets for a hunting round in a Ruger #1 or a bolt-action, but I wouldn't consider that a Garand load.
__________________
.30-06 Springfield: 100 yrs + and still going strong
dmazur is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06420 seconds with 9 queries