The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old June 14, 2011, 03:04 PM   #1
TennJed
Senior Member
 
Join Date: September 26, 2010
Posts: 1,523
45 colt "ruger only" 230 gr lead

i am looking for some heavy recoil or ruger only 45 colt loads for some 230 gr 45 cast lead (round nose or semi wadcutter).

i already have some 2400 and unique so if you have any recommendations for those that would be great.

i am new to reloading so i would be more inclined to want to use a slower burning and/or larger volume powder

thanks
__________________
Find out just how tall I am
By jumping in the middle of a river
TennJed is offline  
Old June 14, 2011, 08:10 PM   #2
Sport45
Senior Member
 
Join Date: May 25, 1999
Location: Too close to Houston
Posts: 4,067
That's a lighter bullet than most use for the "Ruger Only" loads. I think you'll be limited by velocity rather than pressure with that one.

Accurate's Load Guide v3.5 shows 14.8 to 16.4 gr of No.7 under a Montana Cast Bullet 225gr TC for 1087 to 1235 fps.
__________________
Proud member of the NRA and Texas State Rifle Association. Registered and active voter.
Sport45 is offline  
Old June 14, 2011, 09:56 PM   #3
jmortimer
Junior member
 
Join Date: January 24, 2010
Location: South West Riverside County California
Posts: 2,763
Unless you have already purchased or cast the bullets, with a .45 Colt, you really want to go with 250 RFN or 255 swc or even heavier. 2400 is good for hotter loads, with top step being H110/W296.
jmortimer is offline  
Old June 14, 2011, 10:35 PM   #4
TennJed
Senior Member
 
Join Date: September 26, 2010
Posts: 1,523
I acquired about 1200 230gr (about 400 RN and 800 SWC) in a trade and wanted to use them up before I bought some more. wanted to make a few with some heavy recoil for my 4 5/8 blackhawk just to see how it handled.
__________________
Find out just how tall I am
By jumping in the middle of a river
TennJed is offline  
Old June 14, 2011, 10:40 PM   #5
zxcvbob
Senior Member
 
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,184
I like 7.5 grains of Red Dot with 230 grain cast bullets. It's not a max load for a Ruger, but it's got some kick to it. I haven't tried loading bullets that light using a heavy dose of slow powder; I use 250's and 255's for that.
__________________
"The only way to stop a bad guy with a gun is with a good guy with a gun"
zxcvbob is offline  
Old June 14, 2011, 10:47 PM   #6
Para Cassatt
Senior Member
 
Join Date: June 16, 2010
Location: South Carolina
Posts: 117
TJ,
Is the filling of the case more important than high pressure/ high speed?
Leading could become problematic when pushing those light weight bullets at high velocities.
Para Cassatt is offline  
Old June 15, 2011, 07:41 AM   #7
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,237
not guessing

There must be a crimp groove in those bullets so you can mechanically secure them using a heavy non-taper roll crimp (recommend the Redding Profile Crimp die).

If they have no groove do not attempt to make nukes with them, as the bullets will pull forward under recoil and lock up cylinder rotation.
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07270 seconds with 9 queries