The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old June 5, 2011, 03:06 PM   #1
flintlock.50
Senior Member
 
Join Date: July 1, 2009
Posts: 197
chronograph accuracy

I've had a Pro Chrono Digital by Competition Electronics for a couple of years. I get good repeatability on my loads, but they I can't seem to match what the books say or what other folks post for their loads. For example:
.30-06
Rem 700 (22 inch barrel)
165 gr Hornady SSTs
58.0 gr of IMR 4350
Nosler cases
CCI large rifle primers
average MV 2771 fps (10 ft from chrono)
Nosler Accubonds in the same load and cases average 2749 fps

I got 2863 fps in another batch of Nosler cases but they were 20 grains heavier than my current batch so their case capacity was considerably smaller. They never showed signs of over pressure, but I only got 3-4 shots from them before they started showing signs of incipient case head separation.

So here's my dilemma. I have a Leupold VX III scope with the CDS dials. I'm about to order a dial for my 165 grain load. However, if my MV is off the dial won't be correct. What is typical for 58 grains of IMR4350 behind a 165 grain bullet? Are my numbers credible?
flintlock.50 is offline  
Old June 5, 2011, 04:04 PM   #2
PawPaw
Senior Member
 
Join Date: December 24, 2010
Location: Central Louisiana
Posts: 3,113
I'd say your numbers are fairly credible. Factory ballistics charts (I just looked at Federal and Remington) show 2800 fps with 165 grain bullets in .30-06, but you must remember that they're using test barrels in rigidly controlled conditions.

Your rifle is different. My rifle is different. They're all different and will turn in different velocity numbers with the same ammunition.

Trust your testing with your rifle and ammo, with your conditions.
__________________
Dennis Dezendorf

http://pawpawshouse.blogspot.com
PawPaw is offline  
Old June 5, 2011, 04:28 PM   #3
wogpotter
Senior Member
 
Join Date: September 27, 2004
Posts: 3,178
Lets make a couple of assumptions, just for the sake of argument.

Your chrono start screen is not AT the muzzle but is about 10~15 feet away.
That gives you "velocity instrumental at (x) feet" not muzzle velocity. That costs you a tad in measured speed. The factory does calculations allowing for this & giving them "corrected muzzle velocity".

Your barrel is not the exact same length as the one used in the test.
Check this out I went nuts once trying to figure out a published velocity till I read the barrel length, 15" this was for a revolver

Altitude is probably not the same, Humidity & air pressure is probably a little different. Powder, primer & brass/bullet lot #s are definitely not the same.

Add a few things like this together and the 10FPS here & the 25 FPS there add up to maybe a hundred FPS or so. Basically if your data is repeatable & consistent. No unexplained 500FPS "flyers" once in a while & so on your data is probably more accurate for your gun & load than the factory data from their gun applied to your equipment.
__________________
Allan Quatermain: “Automatic rifles. Who in God's name has automatic rifles”?

Elderly Hunter: “That's dashed unsporting. Probably Belgium.”
wogpotter is offline  
Old June 5, 2011, 04:46 PM   #4
Boberama
Senior Member
 
Join Date: January 23, 2010
Posts: 189
You can correct for muzzle velocity by using an online calculator and the ballistic coefficient of your bullet.

So if the chronograph is 10-15 ft away, you can make up the small difference.

Try JBM's calculator, it has an input for chronograph distance.
__________________
I just try to be really, really honest with people when I think that they suck. - Santana Lopez, Glee
Boberama is offline  
Old June 5, 2011, 04:57 PM   #5
flintlock.50
Senior Member
 
Join Date: July 1, 2009
Posts: 197
I use JBM's ballistic calculator lots. It's pretty good.
flintlock.50 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06564 seconds with 9 queries