The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old October 17, 2012, 05:06 PM   #1
Billybob123
Junior member
 
Join Date: October 17, 2012
Posts: 10
Hand held primer

Just getting into rifle and pistol bullet reloading, been doing shotshells for 40 years. Quick question.

What have you found to be the best, and most reliable hand held primer. Will mainly be doing .30 cal rifle rounds but also some .45ACP and .40S&W.

Thanks!
Billybob123 is offline  
Old October 17, 2012, 05:11 PM   #2
PA-Joe
Senior Member
 
Join Date: June 9, 2010
Location: NEPA
Posts: 738
If you go with the Hornady you can use Hornady or RCBS shellholders. If you go with the Lee you need their special holders. RCBS uses a cam shellholder.
PA-Joe is offline  
Old October 17, 2012, 05:51 PM   #3
mrawesome22
Senior Member
 
Join Date: November 9, 2005
Location: Ohio, Appalachia's foothills.
Posts: 3,779
RCBS Universal gets my vote. Works great and no shellholders required.
mrawesome22 is offline  
Old October 17, 2012, 06:13 PM   #4
jepp2
Senior Member
 
Join Date: December 24, 2008
Location: Loveland, CO
Posts: 1,363
I have had excellent service with the Lee hand primers. The Lee tool and the shellholders will cost you much less than any of the other options listed. I didn't select Lee for cost reasons, but have been very satisfied with the performance of their hand primers.
jepp2 is offline  
Old October 17, 2012, 08:41 PM   #5
Hungry
Junior Member
 
Join Date: May 30, 2012
Posts: 3
I've been using the RCBS hand primer for 9, 357 and 45. It works great.

There is some finesse involved with small pistol primers though. Every once in a while one will get turned around, go sideways or get stuck. Not a big deal, but it throws off my rhythm. If it happens, I take a breath and disassemble it. Only happens with small pistol primers.

Mine has the round tray, I'd like to try the diamond shaped one because I think they'd funnel the primers a little bit easier.
Hungry is offline  
Old October 17, 2012, 08:54 PM   #6
William T. Watts
Senior Member
 
Join Date: January 20, 2010
Location: Central Arkansas
Posts: 808
RCBS model 90200 (round tray), I have never experienced any kind of problem with it. I use it for pistol and rifle, quality tool! William
William T. Watts is offline  
Old October 17, 2012, 09:14 PM   #7
jmortimer
Junior member
 
Join Date: January 24, 2010
Location: South West Riverside County California
Posts: 2,763
Lee Precision Ergo Prime. They all work well enough. I will always prime off the press. Fast, comfortable and easy. Here is link to Midway USA with customer/user ratings and comments.
http://www.midwayusa.com/find?sortby...nsionid=12786&
jmortimer is offline  
Old October 17, 2012, 09:19 PM   #8
droptrd
Senior Member
 
Join Date: September 22, 2011
Location: Illinois
Posts: 315
I have the hornady and the rcbs. I really dont like hand primers at all. both of them flip primers occasionally and they both wear my hand out after awhile. Plus you really cant feel what youre doing with them. Im looking into a good bench primer like the rcbs or forster

Last edited by droptrd; October 17, 2012 at 09:25 PM.
droptrd is offline  
Old October 17, 2012, 09:24 PM   #9
Chaz88
Senior Member
 
Join Date: January 4, 2010
Posts: 1,007
When I loaded everything on a single stage I used most of the popular brands, at one time or another, and they all worked fine for me. Now I mostly use a progressive and it get the job done. But I inspect more because not being hands on, like I was for years, leaves some doubt in my mind if everything is primed properly.
__________________
Seams like once we the people give what, at the time, seams like a reasonable inch and "they" take the unreasonable mile we can only get that mile back one inch at a time.

No spelun and grammar is not my specialty. So please don't hurt my sensitive little feelings by teasing me about it.
Chaz88 is offline  
Old October 18, 2012, 12:36 AM   #10
RC20
Senior Member
 
Join Date: April 10, 2008
Location: Alaska
Posts: 2,119
Quote:
RCBS Universal gets my vote. Works great and no shellholders required.
Works great, I have an old Lee hand primer that was really hard on my now somewhat arthritic hands.

The RCBS Universal has much better ergonomic (it may be sold under other names a well

I prefer to hand seat for the better feel comfort of getting it right (just can't feel it on a progressive or a single press).

I got one each for small base and large base. Easy enough to switch but even better not to have to think about it (true a bit of a luxury but well worth it)

I load large rifle with it and huge improvement.
RC20 is offline  
Old October 18, 2012, 07:02 AM   #11
rebs
Senior Member
 
Join Date: January 10, 2012
Posts: 2,285
I picked up an rcbs 90200 used at a gun show for 15.00 and like it a lot. The plastic primer guides were worn a bit so I called rcbs and they sent me new ones for free. Now I like it even more.
rebs is offline  
Old October 18, 2012, 09:12 AM   #12
jcwit
Senior Member
 
Join Date: October 28, 2007
Location: Upper Indiana
Posts: 593
They all work excellant. All depends what you wish to buy.

Myself? I prefer the older one at a time Lee's with the screw in shell holders or a Sinclair primer or the K & M hand primer.
__________________
U.S. Army Veteran
NRA Certified Range Officer
jcwit is offline  
Old October 18, 2012, 02:10 PM   #13
FiveInADime
Senior Member
 
Join Date: January 25, 2012
Posts: 374
Judging by all the reviews on Midway I must have been lucky to get a working Lee Auto-Prime XR. I did drop it and break one of the tabs off on the lid, but that was totally my fault. It works flawlessly for me.
FiveInADime is offline  
Old October 18, 2012, 08:58 PM   #14
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,929
I use a Hornady hand primer for small primers & a Lee auto prime on a press for large .

Been turnin wrenches too long & felling & control of my hands is slowly deteirating, very little feeling in my rt. since shoulder reconstruction.

I`ve used all the hand primers at some point & settled on the Hornady .

They all have different feel though.
__________________
GP100man
GP100man is offline  
Old October 18, 2012, 09:28 PM   #15
serf 'rett
Senior Member
 
Join Date: June 25, 2009
Location: Stuttgart
Posts: 1,383
RCBS has worked good for me
__________________
A lack of planning on your part does not necessarily constitute an emergency on my part.
serf 'rett is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:26 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09752 seconds with 9 queries