The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Tactics and Training

Reply
 
Thread Tools
Old November 27, 1999, 03:27 PM   #1
Dogger
Senior Member
 
Join Date: August 28, 1999
Location: Virginia
Posts: 481
I have a GATCO knife sharpening kit (5 different stones, sharpening oil, and a guide to position the knife at various angles) but I cannot get a sharp edge along the entire blade of a Model 119 Buck Knife. I get a reasonably sharp edge on the straight part of the blade towards the handle, but the curved half out towards the tip defies sharpening. Any ideas? Thanks!
Dogger is offline  
Old November 27, 1999, 08:06 PM   #2
Reloader
Senior Member
 
Join Date: December 29, 1998
Location: Onalaska Tx, USA
Posts: 116
It takes a long time to get an edge on a Buck. You need at least a 4' whetstone, honing oil and a GLASS Dr. Pepper bottle. Hear me out on this. I've been sharpening knives for over 30 years. SAchor the whetstone and maintain constant pressure at a 17 degree angle. Continue this until you can dry shave the hair from your arm, or can slice one of those packing peanuts in half with no resistance. This could take several hours. When it will sry-shave the hair, begin stropping with the Dr. Pepper bottle. It has the best countour for this. You strop it away from you just like you use a whetstone. More sharpening advice is available from www.agrussell.com or www.cutleryshoppe.com. Good luck. Greg
Reloader is offline  
Old November 27, 1999, 11:23 PM   #3
Dogger
Senior Member
 
Join Date: August 28, 1999
Location: Virginia
Posts: 481
Reloader, thanks, but I couldn't make out the third sentence of your post. Looks like a portion of the electrons didn't make it through -- can you repeat that portion of the sentence before "...the whetstone..."? thanks!
Dogger is offline  
Old December 2, 1999, 09:23 PM   #4
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,585
I have found that the desert dust which becomes part of my slip-on boots is just right for that final honing. Like a razor strop with 1000 grit, I guess.
Art Eatman is offline  
Old December 6, 1999, 06:50 PM   #5
Conservative
Member
 
Join Date: November 17, 1999
Location: Goshen, IN USA
Posts: 39
Many people have a difficult time sharpening the curved portion of a blade. This is because it is neccessary to change the position of knife as you stroke through the curve. Because you are getting an ok edge on the straight portion of the blade I suspect that you not changing the orientation of the knife as you sharpen the curved portion.

When sharpening the curve the face of your stone must remain in a plane which is tangent to the curve of the blade. The curved portion of the blade must also remain at the proper angle. When looking at the the straight portion of the blade it will appear as though you decrease the angle between the knife and the stone.

Hope this helps. Thank God for geometry.
Conservative is offline  
Old December 8, 1999, 05:00 PM   #6
Dad2Jane
Member
 
Join Date: November 16, 1999
Location: Nashville, TN, USA
Posts: 95
The reason that I don't buy Buck knives anymore is because they were to hard to get sharp. The best way I found to sharpen a Buck is to take it to a professional and pay them to sharpen it...
Dad2Jane is offline  
Old December 10, 1999, 08:51 PM   #7
Bill Bryant
Member
 
Join Date: September 16, 1999
Location: Deep in the South
Posts: 46
Buy a Sharpmaker 204 from Spyderco. I've sharpened everything from SAKs and kitchen knives to Old Timers and Bucks on it and they will all pop hair off your arm easily.

Very nice product with a helpful video too.
http://www.spyderco.com

Bill Bryant is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:34 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07911 seconds with 9 queries