The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old April 3, 2011, 07:59 PM   #1
papa shooter
Member
 
Join Date: August 20, 2007
Location: South Mississippi
Posts: 63
Browning???

I have two new Browning barrels I want to list for sale but have few questions I need answered before I do. I hope somebody can help me here.
First, I have a NIB 20 guage made in Japan 26" 3" magnum
Second I have a NIB 12 guage made in Japan 30" 3" magnum
Both have vent ribs and fixed choke, now my question. How do I determin the chokes on the barrels? The barrels both say Auto-5 special steel, but nothing about the choke.
Where do I find that?
Thanks for looking.
Papa aka Tim
papa shooter is offline  
Old April 3, 2011, 08:05 PM   #2
seansean1444
Senior Member
 
Join Date: November 28, 2010
Location: ithaca, new york (home of the ithaca shotguns!)
Posts: 395
if u have a caliper you could measure the opening at the back of the barrel and then measure the opening at the front end of the barrel. then subtract the two and the amount of constriction is the choke. like .10 is imp cylinder
seansean1444 is offline  
Old April 4, 2011, 10:54 AM   #3
BigJimP
Senior Member
 
Join Date: February 23, 2005
Posts: 11,420
You can't measure the difference very well with a caliper / because the chamber at the back of the barrel is oversized vs the end that is choked.
You really need a barrel "bore" gague - so you can get an accurate measurement inside vs the end that is choked. Some gun clubs have one that they let "members use" ... but if you go out to a club / and somebody is lounging around ...they will probably check it and help you out. It only takes a few minutes.

But those barrels have to be marked somewhere ... Take the barrel off the gun / and you should see some marks on that barrel.

The older brownings use an asterisk (*) or a set of them to determine the choke of the barrel. (one) * is Full, (Two) ** is Modified, and (three) *** is improved cylinder. This marking is usually located on the side of the barrel along the same line as the mfg's name.

More complete answer BROWNING CHOKES AND THEIR CODES (ON REAR LEFT-SIDE OF BARREL)

'*' designates full choke (F).

'*-' designates improved modified choke (IM).

'**' designates modified choke (M).

'**-' designates improved cylinder choke (IC).

'**$' designates skeet (SK).

'***' designates cylinder bore (CYL).

Last edited by BigJimP; April 4, 2011 at 11:02 AM.
BigJimP is offline  
Old April 4, 2011, 05:29 PM   #4
zippy13
Senior Member
 
Join Date: August 23, 2008
Location: SoCal
Posts: 6,416
I suspect Big Jim is on the right track. Of course, if there are no choke markings, at all, then you may have some rare barrels.
zippy13 is offline  
Old April 5, 2011, 10:40 AM   #5
papa shooter
Member
 
Join Date: August 20, 2007
Location: South Mississippi
Posts: 63
Rare???

I don't see any anything designating a choke. I'll keep looking. If I find them they will be here for sale. So if any body is interested let me know. Both are new in the box barrels. Both marked Auto 5 3" magnum.
Thanks Tim
papa shooter is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:34 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07392 seconds with 9 queries