The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 27, 2011, 11:18 PM   #1
jr 1968
Junior Member
 
Join Date: March 26, 2011
Posts: 5
.44 mag Primer Question?

I have a question that maybe some body can help me with. I bought a new
CVA Scout single shot rifle in .44 mag , and was wondering which is the
hotter primer CCI-350, Fed 155 or Win WLP.

Why I'am asking is right now I'am using CCI-350's and H-110 and it seems to
foul the barrel real quick. Is it because I'am not crimping my cases or the
primer?

I'am new to reloading straight wall cases so I'am clueless.

Thanks,
jr 1968

Last edited by jr 1968; March 28, 2011 at 01:56 AM.
jr 1968 is offline  
Old March 28, 2011, 05:50 AM   #2
RWNielsen
Senior Member
 
Join Date: March 23, 2009
Posts: 109
What's your charge weight? If you go below minimum with H-110 it will be very sooty and can be dangerous as well. Generally there's a very small window between min and max, sometimes only 1 grain. It will need a firm crimp to assure complete ignition. Any LP magnum primer, including WLP should work with it.
Be careful and take care
Richard
__________________
NRA Lifer
RWNielsen is offline  
Old March 28, 2011, 06:19 AM   #3
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 13,914
crimp, Redding Profile Crimp Die.....
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old March 28, 2011, 08:18 AM   #4
Nevmavrick
Senior Member
 
Join Date: January 2, 2010
Location: Sparks, Nevada, near Reno
Posts: 154
I've done a LOT of chronographing with those primers, and very seldom see much difference between them. I've used a lot of WW296/H110 and those primers are quite good for SD.
What bullet are you using? A cast usually doesn't work all that well with the Lee die, but jacketed does OK. If you do a bunch of cast, ya might turn a couple thou off the expander pin. That'll increase the tension on the seated bullet.
Increasing the roll-crimp won't hurt, too.
Have fun,
Gene
Nevmavrick is offline  
Old March 28, 2011, 08:25 AM   #5
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
Hot primers are rarely, if ever, needed with .44 mag. Look to other causes.
Rifleman1776 is offline  
Old March 28, 2011, 02:41 PM   #6
jr 1968
Junior Member
 
Join Date: March 26, 2011
Posts: 5
I'am using sierra 210jhc. and 1 gr. under max according to thier data.
Maybe I need to up the grains some.

Thanks,
jr 1968
jr 1968 is offline  
Old March 29, 2011, 03:12 AM   #7
PunchinPaper
Senior Member
 
Join Date: March 24, 2011
Posts: 148
Jr

Jr i have found that a heavy crimp always give me the best results in the 44mag. Just an idea 2400 also works great in a 44mag case.
PunchinPaper is offline  
Old March 29, 2011, 03:43 AM   #8
Hog Buster
Senior Member
 
Join Date: October 26, 2009
Location: Pointe Coupee, Louisana
Posts: 761
Put a good solid crimp on ‘em. H110 / 296 need to be crimped to ignite properly.
__________________
Those who beat their guns into plows, will plow for those who don't.-Thomas Jefferson
Hog Buster is offline  
Old March 29, 2011, 04:37 PM   #9
wncchester
Senior Member
 
Join Date: December 1, 2002
Posts: 2,828
IME, mag caps (and a good crimp) do help light off ball powders in a .44 mag. (Not really needed with 2400 or 4227 tho.)
wncchester is offline  
Old March 29, 2011, 07:30 PM   #10
Ozzieman
Senior Member
 
Join Date: December 14, 2004
Location: Northern Indiana
Posts: 4,871
I agree with the firm crimp.
I shoot H110 out of a Ruger 77/44 and have very little fouling. There is some powder residue but it’s been very clean but I also load hot.
Ozzieman is offline  
Old March 29, 2011, 08:03 PM   #11
GeauxTide
Senior Member
 
Join Date: April 20, 2009
Location: Helena, AL
Posts: 3,038
As stated, firm crimp; however, a heavy bullet pull is in order with heavy charges of H110/296. Your sizing die should bring the case to minimum spec.
GeauxTide is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:02 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09785 seconds with 7 queries