The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old March 9, 2011, 03:12 PM   #1
JJewell
Junior Member
 
Join Date: March 9, 2011
Posts: 2
Win Model 52 Barrel Band

Hi All

I have a Model 52 Winchester target rifle that I recently purchased. The rifle had the barrel band removed. I installed a 20X Fecker scope and the rifle shoots dead on - 1 MOA at 100 yards or less. I am looking for advice regarding whether to add the missing barrel band and/ or to merely float the barrel.

Jim
JJewell is offline  
Old March 9, 2011, 09:46 PM   #2
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
I'd shoot it quite a bit more, before I made any major decisions like that, about it.

YMMV, of course............................

.
PetahW is offline  
Old March 10, 2011, 10:01 AM   #3
triggerman770
Senior Member
 
Join Date: August 9, 2009
Location: Metro Atlanta Area
Posts: 125
barrel band

it was made with the band and will probably shoot better with it. 1" group is big for a 52
__________________
Small Arms Restoration, Inc.
smallarmsrestoration.net
Proud member of Georgia Carry.org
www.georgiacarry.org
triggerman770 is offline  
Old March 11, 2011, 12:31 PM   #4
JJewell
Junior Member
 
Join Date: March 9, 2011
Posts: 2
Thank You

I suspected that it would benefit from original equipment however I see so many with the band removed and I understand that free floating the barrel with a pillar bed helps. It does on every other rifle (bolt action) that I own.
JJewell is offline  
Old March 17, 2011, 04:52 AM   #5
Bart B.
Senior Member
 
Join Date: February 15, 2009
Posts: 4,378
Winchester put barrel bands on their early rimfire match rifles just like Springfield M1903 30 caliber target rifles had. They thought that was the way it was supposed to be made. 'Twas finally stopped on their later Model 52's and they shot much better that way.

Over the years, top competitive shooters learned that nothing should touch the barrel except the receiver; no bands, tuning screws, shims, worms or anything else between the barrel and fore end. The reason is that when a sling's attached, using it in position tends to bend the fore end a tiny bit changing its pressure on the barrel. That makes the barrel vibrate/whip different for each shot 'cause nobody holds a rifle with the same forces and position for each shot. So, make sure the barrel's free floating.

The receiver doesn't need to be pillar bedded; conventional bedding is just fine. Anschutz rimfire match rifles came without bedding; just bare metal to wood around the receiver. Torquing the stock screws to somewhere between 20 and 30 inch pounds is about right. Pillar bedding came about because the first synthetic stocs had cores in the receiver area too soft to withstand stock screw torque at this level and higher. Wood stocks never had this problem. The most accurate rifles I know of have all been conventional epoxy bedding; no pillars needed.
Bart B. is offline  
Reply

Tags
barrel barrel , win 52

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06352 seconds with 7 queries