The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > NFA Guns and Gear

Thread Tools Search this Thread
Old February 13, 2011, 02:20 PM   #1
Senior Member
Join Date: November 2, 2005
Posts: 1,013
Correcting Errors on ATF forms

Has anyone here ever submitted an ATF form only to have it kicked back because of errors which need to be corrected? Do they care if you use "white out"?
dajowi is offline  
Old February 13, 2011, 02:27 PM   #2
James K
Join Date: March 17, 1999
Posts: 22,056
Those forms are not that complex; I would just get new forms and redo them, not use whiteout or stick-on tape.

Jim K
James K is offline  
Old February 13, 2011, 03:10 PM   #3
Senior Member
Join Date: February 7, 2011
Location: NE Ohio
Posts: 246
I would second Jims advice but if there is some reason using new forms is problematic, I would not use whiteout, tape, or marker to black it out. Draw 1 single black line through the incorrect info, write in the correct info above, below, or beside it (use judgment here) and then initial each and every change. It's worked on every government form I've ever used it on, dating back 30 yrs or so.
tgreening is offline  
Old February 16, 2011, 12:21 AM   #4
Junior Member
Join Date: August 29, 2010
Location: Umpqua, Oregon
Posts: 8
Submitting new forms is sometimes (often?) not an option. In Dajowi's case, the returned forms were the original that were submitted to NFA and contained the buyer's (me) photos and, more importantly, the chief LEO's info and signature. Since we had to modify the original forms, it was Dajowi's good call to line-out the old info, initial it and resubmit with updated info.

Some valuable info was learned here, which is, I'm sure, obvious to those more experienced in such matters. First, the firearm descriptions have to match exactly between both Form 4s on a person-to-person transfer. Any deviance will get it bounced back.

Second, NFA discovered a discrepancy that neither the seller, the buyer nor the gun's original seller had noticed. The original Form 4 on a suppressor, completed by an SOT over a dozen years ago, had an "i" in place of a "1," which naturally caused some confusion to the examiner. She asked that a photo of the suppressor's S/N be sent to her with the amended Form 4 info, which was done.

Both Dajowi and I seem to agree that this was not a BS-kinda deal. The examiner actually caught a few discrepancies and/inaccuracies and sought to have them corrected. Better now than at some time in the future when, if numbers don't match up, it might prove ugly in the field. Or the cell.

macscott is offline  
Old February 19, 2011, 08:08 PM   #5
Join Date: January 17, 2010
Location: Eastern Shore Md.
Posts: 16
I had 16" vector53 Form1d and cut to 8": in the barrel length and overall length I had put "less than16inches" and "less that 26inches"...
when they send it back i called them, only had to scratch it out and then initial it and then return to nfa branch. no problem.
vc1911 is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 04:29 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2015 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.10383 seconds with 7 queries