The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools
Old February 11, 2011, 11:37 AM   #1
mec
Senior Member
 
Join Date: December 6, 2001
Posts: 1,530
FN 1910 380

Can anybody explain some of the details of this pistol> The serial number is in the high 600,000 range and may be post 1968. The barrel bushing appears to be from one of the post GCA elongated/target sighted Browning 380s, The address line is quite a bit different than vintage FNs I have found on line
Attached Images
File Type: jpg addline1910.jpg (63.9 KB, 394 views)
mec is offline  
Old February 11, 2011, 04:55 PM   #2
spacecoast
Senior Member
 
Join Date: October 14, 2009
Location: Sunshine and Keystone States
Posts: 4,152
Found this article -

http://world.guns.ru/handguns/hg/be/...d-m1922-e.html

It bears some superficial resemblance to the Colt Hammerless .380 of 1908 and the design has many of the same features - grip safety, 7 round capacity, etc.
spacecoast is offline  
Old February 11, 2011, 06:51 PM   #3
gyvel
Senior Member
 
Join Date: August 30, 2009
Location: Northern AZ
Posts: 5,229
The FN 1910's continued to be produced well into the 1980's (ca. 1984, if I recall correctly), so what you have is a gun that was made for sale in Europe or other parts of the world where "Browning Arms Company" marked arms were not sold. BAC marked arms were, by agreement, sold in North America, while the "FN" marked guns were sold in the rest of the world.

The very last gasp variant of the 1910 before it was dropped also had the squared off rear end on the slide with a protruding cocked firing pin indicator, much like the "10/70" Models that were sold in the U.S. after the GCA of 68.

You'll also notice that your grips are very similar to those found on "BAC" marked guns, i.e. the sides tend to be a bit more vertical and the checkered areas are more or less flattened.
gyvel is offline  
Old February 11, 2011, 08:37 PM   #4
mec
Senior Member
 
Join Date: December 6, 2001
Posts: 1,530
So, it appears that this must be made concomittant with the bAC arms- a fairly late production with co-mingled features. ????
If this is post 68, I wonder how it got into this country-maybe only indifferently legal?
The barrel bushing is a conundrum. Does anybody know if the FN bushings were prone to shere off and launch from the gun? Numrich doesn't seem to have any replacements on hand and it is posible that somebody busted the original bushing and replaced it with whatever was available- ie: a bushing form the importable target model.???
mec is offline  
Old February 11, 2011, 11:39 PM   #5
gyvel
Senior Member
 
Join Date: August 30, 2009
Location: Northern AZ
Posts: 5,229
Yes, you are correct; BAC marked and FN marked guns were all sold concurrently in different parts of the world. How yours got in the US is anyone's guess, but the possibilities are endless. Many guns have been smuggled in by tourists, brought back by GI's or airline employess, or it could have even been brought to the US by a European/Canadian transplant. Who knows?

Regarding the barrel bushing, while (fortunately) it is not too common of a problem, the barrel bushings can and do fly off while being shot (especially if not properly seated), or lost when launched by the recoil spring during reassembly. The style that is on your gun is a late pattern made by FN, and it most likely is a replacement for one that was lost, but it is possible, depending on how close you are to the 700,000 range, that it is original. In general, they are a lot easier to get on and off than older style bushings.

Numrich is usually out of most everything that you need, and Browning hasn't had them for years, but they are out there if you look around.

One possible source is Western Gun Parts ( www.westerngunparts.com ), in Edmonton, Alberta, Canada. Jeff Heimann started out a few years ago selling parts on eBay from his retired father's business (including Browning Parts Distributor), then expanded into a fairly large gun parts company. I have always had good luck with them.

I just checked www.Marstar.ca website and they are out of them, too.

If you'll also notice, your grip safety is a bit diffferent than earlier guns as well.

I was also going to have you check your trigger to see if it was plastic, but I can see blue wear on it. Some later 1910's have plastic triggers (as well as the FN "Baby" .25's).

Last edited by gyvel; February 11, 2011 at 11:49 PM.
gyvel is offline  
Old February 12, 2011, 03:15 AM   #6
mec
Senior Member
 
Join Date: December 6, 2001
Posts: 1,530
Glad to say, it has no plastic on it. Thanks for the information. this one does have the cocked striker indicator on the back of the slide but I like to reassemble the gun uncocked to keep tension off the spring in storage.
mec is offline  
Old February 24, 2011, 06:47 AM   #7
BlueTrain
Senior Member
 
Join Date: September 26, 2005
Location: Northern Virginia
Posts: 5,825
Skeeter Skelton wrote that this gun, as well as others that became prohibited by the Gun Control Act of 1968, could still be purchased by law enforcement agencies or possibly individual officers but I have no idea how that may have worked. Possibly there were some police supply houses or gun dealers that did that sort of thing.

In the same way, Washington, D.C. residents can legally buy handguns now but there are no gun shops in the district. All gun purchases there go through one dealer.
__________________
Shoot low, sheriff. They're riding Shetlands!
Underneath the starry flag, civilize 'em with a Krag,
and return us to our own beloved homes!
Buy War Bonds.
BlueTrain is offline  
Old February 25, 2011, 04:39 AM   #8
gyvel
Senior Member
 
Join Date: August 30, 2009
Location: Northern AZ
Posts: 5,229
As far as I'm concerned the FN/Browning 1910 is one of the finest pocket autos ever produced. I have carried one for over 30 years.

A number of years back there was a company (in Texas, I think) that was going to make a reproduction of it, but, apparently, it never got off the ground. There was a photo of a prototype in Gun Digest.

Last edited by gyvel; February 27, 2011 at 11:42 AM.
gyvel is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:39 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08144 seconds with 10 queries