The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old August 24, 2012, 07:32 PM   #26
Amsdorf
Junior member
 
Join Date: July 24, 2011
Location: Saint Louis, Missouri
Posts: 849
Pictures? Please?
Amsdorf is offline  
Old August 24, 2012, 08:16 PM   #27
Doctor H
Junior Member
 
Join Date: August 24, 2012
Location: California
Posts: 3
1847 walker just arrived

Thanks Hellgate and mykeal---I just want to take this slowly. I really love this piece! I compared it to my 1860 Army and the size differential is truly amazing. I will double check everything, like the direction of entry---you just never know.
Doctor H is offline  
Old August 24, 2012, 09:36 PM   #28
Chowmif16
Member
 
Join Date: April 22, 2012
Posts: 65
Felt wads and yellow jackets!

I'm with Doc Hoy on the felt wad issue. I have shot percussion revolvers for 16 years and always thought that felt wads were for people who wanted to spend money...
I usually used cream of wheat or nothing, and smothered crisco over the ball to help with fouling. After seeing the post on home-made wads, I just bought the felt and beeswax to make them on the cheap.

I do believe that this is the first time I've heard of shooting wasps with a pistol! Well done. I did once shoot a wasp's nest with a full chamber of powder and no ball. Big black spot on the roof of the shade canopy, and no nest remaining...

As mentioned in a previous post, there is a wealth of info on cap n ball revolver shooting/tuning here and on other forums.
Chowmi
__________________
Chowmi

Fighter Pilot, Black Powder Afficionado, and skeptic.
Chowmif16 is offline  
Old August 25, 2012, 12:48 AM   #29
ROGER4314
Senior Member
 
Join Date: May 17, 2009
Location: East Houston
Posts: 257
Thumbs up on the wedge being installed too tightly.

Flash
ROGER4314 is offline  
Old August 26, 2012, 12:35 AM   #30
Whetstone70
Junior Member
 
Join Date: August 22, 2012
Location: Texas, Arizona
Posts: 6
Shims

On my Pistols I cut round Shim from machinist shimstock or you can use feeler gauges for shimstock. This puts an end to the arbor dilemma and you can adjust as fine as you want.
__________________
To all Fire,Police and Armed Services. Thank You
OIF 05-06 08-09
OEF 10-11
VFW Life Member
Whetstone70 is offline  
Old August 27, 2012, 12:37 PM   #31
Doctor H
Junior Member
 
Join Date: August 24, 2012
Location: California
Posts: 3
1847 Walker Just Arrived

Regarding the tight wedge issue [again]---I double checked that I was inserting the wedge from the right side, which I was, and I also did some minimal lubing to the wedge to ease the fit. Bottom line, it was still tough to insert.

I then fully removed the wedge and looked into the arbor---again remembering I am new to black powder guns, I noticed that there appeared to be two protrusions into the rectangular arbor: they are likely circular in cross section, and looking in from the right side of the Walker, the closer one is on the right, the one on the far side is on the left.

My suspicion (please correct me if you know) is, if these are not flaws, that these help to align the wedge when reinserted. However, I watched a "YouTube" video of cleaning/reassembling the Walker and the young man in the video reinserted the wedge with thumb, not plastic hammer, pressure.

I have e-mailed Cabelas on this but would like you input---perhaps time, and wear will make insertion easier but I just want to insure this is not a flaw.

Thanks much and I have really appreciated the help.
Doctor H is offline  
Old August 27, 2012, 12:38 PM   #32
Doc Hoy
Senior Member
 
Join Date: October 24, 2008
Location: Chesapeake, VA
Posts: 4,598
Photos...

A photo would be helpful here.
__________________
Doc

My reading of history convinces me that most bad government results from too much government. Thomas Jefferson
Doc Hoy is offline  
Old August 27, 2012, 05:57 PM   #33
Shotput79
Senior Member
 
Join Date: March 20, 2011
Location: NC
Posts: 177
When I bought my first Uberti Dragoon I noticed that most all the Dragoons the man had in the case had the same problem with the wedge you could take your finger and push the wedges back and forth. I went on and got the one I wanted anyway and after firing a couple cylinders full it went to working like it should. I tried to show the guy in the store what was causing the problem that the wedge was almost bottomed out and the cylinders were hard to turn when you pulled the hammer back. I think he was more in to getting them sold than lessing to me. I mean what the heck do I know.
Shotput79 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:16 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07401 seconds with 7 queries