The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: General Handgun Forum

Reply
 
Thread Tools
Old January 6, 2011, 01:18 AM   #1
pilpens
Senior Member
 
Join Date: April 24, 2008
Location: Ohio
Posts: 1,391
124 vs 147 grain HP 9mm ?

Is 147 HP better than 124 HP for self defense (same bullet design , same pistol with 4" barrel)?
Is there a difference? Does it matter for self-defense purposes? Penetration issues?
Just trying to up the power of 9mm pistol which is normally loaded with 115s.
pilpens is offline  
Old January 6, 2011, 02:39 AM   #2
derekb
Member
 
Join Date: January 2, 2011
Location: Indiana
Posts: 73
'Power' is a function of both bullet mass and velocity. In most guns (firearms and otherwise), replacing a lighter, faster projectile with a heavier, somewhat slower projectile will show improvements in energy to a point, before the curve heads back down. I don't know if you can generalize far enough to say that every 147 grain bullet will carry more energy from any given gun than a 124 grain bullet, or vice versa.

I'm sure someone more well-versed in ballistics and terminal performance can either provide an immediate generalization, or offer links to performance testing.
derekb is offline  
Old January 6, 2011, 03:13 AM   #3
Sixer
Senior Member
 
Join Date: April 16, 2008
Location: Missouri
Posts: 1,891
I wouldn't want to get shot with either.
__________________
Hopp Custom Leather <------ click for HOLSTER awesomeness!!

-There is no theory of evolution... Just a list of creatures Chuck Norris has allowed to live.
Sixer is offline  
Old January 6, 2011, 03:58 AM   #4
Action_Can_Do
Senior Member
 
Join Date: May 28, 2005
Posts: 227
147 hollowpoints aren't as popular as the lighter ones due to expansion issues. The bullets simply don't move fast enough to give reliable expansion. The most popular self-defense loads for the 9mm are 115 gr +P hollowpoints.
Action_Can_Do is offline  
Old January 6, 2011, 05:38 AM   #5
mete
Senior Member
 
Join Date: June 14, 2004
Location: NY State
Posts: 5,364
The adoption of the 147 was based on nonsense .The early ones were poor the newer ones better.
I stick with the 115-124 gr .For more effective rounds use +P premium rounds.
__________________
And Watson , bring your revolver !
mete is offline  
Old January 6, 2011, 05:50 AM   #6
Hal
Senior Member
 
Join Date: October 9, 1998
Location: Ohio USA
Posts: 7,435
I'm all about accuracy...

124 gr shoot better. (YMMV)

W/near .357mag (from a "snub nose") velocities for the 124gr. +P 9mm out of a Hi Power or CZ75b, I see little reason to use the 147.
Hal is offline  
Old January 6, 2011, 06:11 AM   #7
Hal
Senior Member
 
Join Date: October 9, 1998
Location: Ohio USA
Posts: 7,435
oops - double tap!.
Hal is offline  
Old January 6, 2011, 06:58 AM   #8
TacticalDefense1911
Senior Member
 
Join Date: April 4, 2006
Location: Ohio
Posts: 1,276
The new 147 grain loads are much better than the old ones which had issues expanding reliably and not functioning properly in guns. If you choose a newer design you should be just fine. If you can find it, the 147gr. Federal HST load is very impressive. Some 147's are better than some 115's or 124's and visa versa. Personally, I stick with 9mm loads in the 115-124 grain range. Not that its right, just my preference. There are a lot of good loads for 9mm anymore.
TacticalDefense1911 is offline  
Old January 6, 2011, 07:31 AM   #9
1goodshot
Senior Member
 
Join Date: November 11, 2001
Location: chandler,az
Posts: 863
Imo the only reason to shoot 147gr bullets is if you use a surpressor otherwise I use 115gr in the 9mm.
1goodshot is offline  
Old January 6, 2011, 09:10 AM   #10
Adamantium
Senior Member
 
Join Date: June 6, 1999
Location: El Paso, TX
Posts: 992
Design is more important than weight, every single bullet, every single time. There is nothing wrong with modern 147's because nowadays they are being designed to shoot and expand from normal sized guns are are no longer considered SMG rounds.

My personal favorite HP's are Hornady XTP's because they are a controlled expansion bullet in that they are designed to stop expanding at a certain point to ensure penetration. So what you have is a 115, 124 and 147 bullet that will all expand to approx the same diameter but with the 124 and 147 each penetrating further than the next. I keep my gun loaded with 124's and don't feel +P as needed for a 4 inch barrel.
Adamantium is offline  
Old January 6, 2011, 09:17 AM   #11
MrAcheson
Senior Member
 
Join Date: July 15, 2002
Posts: 442
A big difference is that you might be able to get +P 124 grain JHPs. Because of case capacity issues, 147s are almost always standard pressure. This means that the 147s generally have more momentum but less energy than the 124s.
Quote:
Design is more important than weight, every single bullet, every single time.
This. There are old 147s that suck. There are a lot of old 124s and 115s that suck too. Buy decent carry ammo.
__________________
These views are not representative of those held by the US Army, DoD, or US Government.
Jeffthebaptist.blogspot.com
MrAcheson is offline  
Old January 6, 2011, 09:29 AM   #12
.22lr
Senior Member
 
Join Date: July 14, 2007
Posts: 239
Much Ado About Nothing

The differences in quality ammunition are so small that they barely matter. The person getting shot will never know the difference.

If anything needs to be worried over, it should be the reliability of the ammunition in your firearm. After that, the pursuit of quality training and competence, not picking nits over which bullet gives you 10 Newtons (I prefer physics in metric) more energy.

VR

Matt
.22lr is offline  
Old January 6, 2011, 09:31 AM   #13
Fargazer
Senior Member
 
Join Date: October 4, 2010
Location: Chattanooga, TN
Posts: 466
Here are some posts (on various forums) that I've used to decide what 9mm bullet weight to use:I personally go with 147 grain weight for the following reasons, in order:
  • they are more accurate in my P99
  • Remington Golden Saber's run flawlessly through my P99
  • I can get good pricing per round on 50 count boxes of 147 grain Golden Saber
IMHO, each gun is going to have it's own "sweet spot" for ammo weight and performance. For me and my P99, I ran almost a thousand rounds through it before settling on my SD ammo. Soon I'll have a 9mm P99c AS, at which time I'll once again run through different ammo weights and brands to find it's sweet spot. I hope it's also 147 (simplifies ammo reloading / purchasing), but it may not be.

As always, YMMV - Fargazer
Fargazer is offline  
Old January 6, 2011, 09:48 AM   #14
TBT
Senior Member
 
Join Date: January 24, 2005
Location: Pittsburgh Pa
Posts: 773
As has been already said, the idea that the 147 grain bullet doesn't expand is obsolete when talking about modern designs. They expand and they do well. Frankly though, expansion isn't much of a consideration for me. I look at it like a bonus. I'll take it if it's there but only if it doesn't kill penatration to achieve it. IMHO, penatration is much more important and in that, the 147 usually excels.

That being said I really don't think there is a ton of difference. I shoot what works and is accurate in my gun. Currently I'm running Ranger 127's in my M&P.
TBT is offline  
Old January 6, 2011, 12:14 PM   #15
8shot357
Junior member
 
Join Date: September 7, 2010
Posts: 1,740
From all I know, is the 124g is the perfect compromise. I have GDHP 124g +Ps in all my 9mm's, all two of them. Actually my last 5 shots are 115g Fiocchi +P+ FMJs Nato's (cross circles).

Last edited by 8shot357; January 6, 2011 at 12:29 PM.
8shot357 is offline  
Old January 6, 2011, 01:00 PM   #16
Burger
Senior Member
 
Join Date: November 2, 2010
Posts: 152
It's like comparing a 300hp camaro (gets there faster) vs a 300hp suburban (pushes through harder).

throw a +P into the equation (more gun powder)

It's like comparing a 400hp camaro vs a 400hp suburban

For SD and HD, I say go for the heavier projectile.

I likie them 230 grains bestest

If you don't think the shot will penetrate, then either the target is in full body armor or you are standing too far away from the target and you should run the other way instead of shooting.

Last edited by Burger; January 6, 2011 at 01:07 PM.
Burger is offline  
Old January 6, 2011, 01:11 PM   #17
Mobuck
Senior Member
 
Join Date: February 2, 2010
Posts: 2,225
I've tested 124 and 147 grain Gold Dots from my Ruger P95 (3.9" barrel) on water jugs. This is not meant to be equal to a gelatin test but a comparison of the two bullets. The 147 penetrated roughly 50% further with a smaller amount of expansion and apparent damage. I'll stick with the 124 grain for my pistol and use the 147's in my PC9 carbine where they show excellent performance.
Mobuck is offline  
Old January 6, 2011, 10:57 PM   #18
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,242
testing on people

People-shooting tests have confirmed that 115--127g JHPs going fast work superbly.
Think 115g +P+. (Think Secret Service, who recently switched from 9x19 to 357 SIG for more of the same).
Think 124--127g +P. (Think 357 Magnum, 357 SIG, 9x23; Texas DPS who switched from 45 ACP to 357 SIG for "better performance").

Think "high velocity medium-weight projectiles ranging from 115g up to 127g launched at +P pressure".



Notice no mention of 147g?
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old January 6, 2011, 11:39 PM   #19
cougar gt-e
Senior Member
 
Join Date: July 25, 2009
Posts: 809
In my mind, I used to obsess about caliber differences, bullet weight, construction, etc etc etc:barf: Now, I just concentrate on hitting the second button from the top. Do that every time and it really doesn't matter what you used. 380, 9, .40 or .45. Holes there turn the traffic light from green to red for the BG.
cougar gt-e is offline  
Old January 7, 2011, 03:10 AM   #20
Hook686
Senior Member
 
Join Date: May 22, 2005
Location: USA The Great State of California
Posts: 1,930
Different strokes for different folks. I like the momentum advantage of the higher weight projectiles. I use Buffalo Bore 147 grain.

http://www.buffalobore.com/index.php...duct_list&c=26

9mm Luger +P+ Pistol and Handgun Ammo
9mm Luger +P+ Pistol and Handgun Ammo - (+P+) 147 gr. Jacketed Hollow Point (1,175 fps/M.E. 451 ft. lbs.) -
__________________
Hook686

When the number of people in institutions reaches 51%, we change sides.
Hook686 is offline  
Old January 7, 2011, 08:24 PM   #21
psyshack
Junior member
 
Join Date: May 27, 2010
Posts: 159
I load my own.

Winter I use a 147gr XTP on the +P side of life. The rest of the seasons 124gr XTP +P loads. Load up until I start loosing accuracy and or flatting the primers. Which ever comes first. I can run hotter loads in the Sigma that the PF-9.
psyshack is offline  
Old January 7, 2011, 11:09 PM   #22
Tom Servo
Staff
 
Join Date: September 27, 2008
Location: Foothills of the Appalachians
Posts: 10,332
Quote:
Texas DPS who switched from 45 ACP to 357 SIG for "better performance"
Heresy. Absolute heresy.

It's very simple. We all know that the 9mm simply will not kill anything. While it may cause some surface irritation, and possibly induce an infection, it is not a tenable self-defense loading. The only reason our military uses it is because ammo is cheap, and it's compatible with what the Dutch or whoever are using.

If I absolutely had to trust my life to such a meager loading, I would likely choose the 115gr or 124gr loadings. I know of no current factory handgun sighted in for 147gr, and some will have problems cycling it. You should be practicing with something that prints reasonably close to the same POI as your defensive ammunition, and there's not much 147gr ball out there.

(Oh, and all but the last two sentences are in jest )
__________________
Sometimes it’s nice not to destroy the world for a change.
--Randall Munroe
Tom Servo is offline  
Old January 9, 2011, 02:39 AM   #23
bamaranger
Senior Member
 
Join Date: October 9, 2009
Location: North Alabama
Posts: 4,354
147 v. 124

When my outfit went from round guns to flat ones, the universal transition pistol was a SiG P228 and the issue load was the 9mm 147 gr JHP.

Stories began to circulate immediately and one was that the 147 JHP was never intended as a pistol ctg but was for use in suppressed sub guns, namely the MP-5. Unknown if there was truth to this or not.

What was pretty evident was that in the use of the 9mm for finishing off deer, in deer v. car MVA's and dealing with an occasional feral domestic animal, the 9mm/147 from the stubby P228 seemed weak. Sorry, the agency does not have a lot of shootings v. felons.

When the opportunity came to "upgrade" from the transitional 9mm, to either .40 or .45, a huge percentage of personnel did, mostly to .40, the old guard to .45.

The 147 ammo largely disappeared as it was shot up in quals and training, and those few that retained the 9mm switched to 115 or 124.
bamaranger is offline  
Old January 9, 2011, 09:30 AM   #24
ClydeFrog
Junior member
 
Join Date: May 1, 2010
Posts: 5,798
Ranger T 127gr +P+ JHP, Corbon DPX load...

In 9x19mm or 9mmNATO, I'd say the top pick for general carry/duty/protection is the highly rated Winchester Ranger T 127gr +P+ JHP. My local PD(around 900 sworn LE officers) uses the 127gr JHP 9mm load for their "new" SIG P226 sidearms.
As for the posted topic, I'd choose the 124gr load. It has similar ballistics & recoil or milspec training-practice rounds or carry/duty rounds.
Many like the 147gr designs, but I'd select a 124gr +P or maybe a 115gr +P+ JHP. CorBon/DPX, DoubleTap Ammo, Speer Gold Dot, Remington Golden Saber(bonded) all have great 9x19mm loads available to the general public.
ClydeFrog is offline  
Old January 9, 2011, 11:33 AM   #25
pilpens
Senior Member
 
Join Date: April 24, 2008
Location: Ohio
Posts: 1,391
thanks for the input.
I guess, I will stick with what I carry now, 115s and 124s.
pilpens is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:31 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.13321 seconds with 7 queries