The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 22, 2010, 02:19 AM   #1
micksis86
Senior Member
 
Join Date: June 16, 2009
Posts: 420
Polishing the action of my Marlin Lever action

I wanna do some polishing of the action of my marlin 1894 just to slick up up the action a bit. I've read alot of info and i'm confident of doing it without too much trouble.

However i'm wondering what the best medium is to use for polishing i've read places that suggest 400grit wet 'n dry paper. Any other suggestions or tips to do with the job?
__________________
Never argue with morons, they will lower you down to their level and beat you with experience.
micksis86 is offline  
Old November 29, 2010, 02:02 AM   #2
50of4064
Member
 
Join Date: April 20, 2009
Location: Southern Calif.
Posts: 48
question.

Not familiar with that model so I must ask is it a Brass action or a Steel action?
It would seem that any sand paper would leave lines, so if the finish you are looking for is a mirror finish try polishing it on a buffing wheel with the correct type of buffing compound. You will find it will take off blued finish and small imperfections in the surface.

Hope this is of some help
50of4064 is offline  
Old November 29, 2010, 11:07 AM   #3
mapsjanhere
Senior Member
 
Join Date: August 6, 2009
Location: Albuquerque
Posts: 2,344
I think he's referring to the internal parts of the action. I would use a fine stone, and only go to wet sandpaper (mounted on a really flat surface, chunk of polished granite sample works great) if you see the stone isn't doing the job because the ridges are too big. Using sand paper free hand it's very easy to round over corners that aren't supposed to be rounded, and having to add shims where none were needed before because you took off too much material to get that machining mark out.
__________________
F 135 - the right choice
mapsjanhere is offline  
Old November 29, 2010, 01:11 PM   #4
natman
Senior Member
 
Join Date: June 24, 2008
Posts: 1,375
This is what you should use:

http://www.brownells.com/.aspx/pid=1...NSAS_STONE_SET

Not cheap, but you can use them for the rest of your life. Keep the stone oiled.

You can do it with OILED sandpaper stretched over a file, but believe me after you've had the sandpaper tear & slip a few times the Arkansas stones will be worth every penny.

This is NOT an activity where if 2 strokes are good, then 4 strokes are better and 10 strokes is the ultimate, so you should use 20 strokes. Stoning is in effect putting years of wear on your parts and you want to do it slowly and right. The idea behind using a stone is to knock off the high spots while removing the minimum amount of steel. That's all you want to do. Resist the temptation to stone some more to make the surface "perfect".
natman is offline  
Old November 29, 2010, 01:14 PM   #5
hickstick_10
Senior Member
 
Join Date: August 8, 2009
Posts: 477
Lop a couple coils off the mainspring and it will do wonders.

Plus a new spring is much cheaper and easier to procure then a new bolt, receiver or hammer

Your best bet is to just use the gun more.
hickstick_10 is offline  
Old November 29, 2010, 01:16 PM   #6
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
Poor Man's Action Job

Most owners of new Marlins would be surprised, and benefit, at/from the results of a few night's simple homework, while watching the boob tube, whatever.

After ensuring the rifle & magazine are both empty, apply a thin coating of FINE valve grinding compound (diluted with oil) to the bolt channel and sides of the lever tip (inside the bolt slot).

Cycle the action constantly for a few hours on/off each evening, or until you drive your family crazy - whichever comes first.

When done, clean out ALL the compound with kerosene, relube the action, and give it a try.

.
PetahW is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:28 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06845 seconds with 7 queries