The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 7, 2010, 01:54 AM   #1
oldcars
Senior Member
 
Join Date: March 13, 2007
Posts: 375
Remington 700 ADL stock cut open to BDL ?

Hello, I was wondering if anyone here has ever converted a wood ADL stock to fit BDL bottom metal? when holding the stocks side by side it seems like it would be pretty simple, just carefully cut open the bottom of the stock and inlet around the foreward action screw, is that it? I know I will also have to mill down the ADL magazine box a little.
oldcars is offline  
Old November 7, 2010, 09:36 PM   #2
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,658
Well, I don't know how simple it is, but that is exactly what needs to be done. Leave the magazine box until last; you might not have to do much at all.

Jim
__________________
Jim K
James K is offline  
Old November 7, 2010, 10:18 PM   #3
sc outdoorsman
Senior Member
 
Join Date: November 23, 2009
Location: Western SC
Posts: 208
You may find this helpful Brownells sells the kit and has a short video to go along with it. I have thought about doing this myself but decided if I do it I will get a new bdl stock instead of cutting the existing one.



http://www.brownells.com/.aspx/pid=3...DL_TO_BDL_KITS


http://www.brownells.com/.aspx/lid=1...onversion_Kits
sc outdoorsman is offline  
Old November 8, 2010, 05:19 PM   #4
oldcars
Senior Member
 
Join Date: March 13, 2007
Posts: 375
Hey guys, thanks for the replys. After much thought, I just ordered a new BDL mag box (it was only $11) and a new Boyds stock. I think I'll just sell the ADL stock, I was never crazy about the factory checkering anyway and by the time I sand it down and re-shape it a bit I might as well start with what I want and get some money out of the factory parts to help offset the new purchase.
oldcars is offline  
Old November 10, 2010, 09:43 PM   #5
publius
Senior Member
 
Join Date: January 25, 2005
Location: Mississippi/Texas
Posts: 2,453
Wise decision, trying to inlet to BDL configuration would have driven you crazy and probably not turned out to your satisfaction. Sell the ADL stock and recover some of your costs.
__________________
"Suppose you were an idiot, and suppose you were a member of Congress, but I repeat myself." Mark Twain
publius is offline  
Old November 12, 2010, 07:33 PM   #6
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
The first deer gun I bought, after I was discharged from the service in the mid-60's, was a .243 Remington 700ADL that I converted to BDL as above soon after I bought it for $95 OTD.

I ordered the BDL bottom metal (TG/FP) only, directly from the Remington Parts Dept, for about $20 then IIRC - because the mag well liner & follower springs were the same for either ADL or BDL.

It took about 30mins to cut out the floor of the blind magazine well in the wood stock and inlet the bottom metal satisfactorily.

I later used a DemBart checkering tool, run in the impressed checkering, to convert the negative/pressed checkering to regular, positive checkering diamonds.
THAT took a little longer than 30mins.

.
PetahW is offline  
Old November 24, 2010, 12:47 PM   #7
PanHeadRed
Junior Member
 
Join Date: November 24, 2010
Posts: 1
Any of you guys wanting to sell a 700 BDL short action stock let me know, I am looking for plastic but wood might be ok.

Regards,
PHR
PanHeadRed is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06663 seconds with 7 queries