The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old October 16, 2010, 02:58 PM   #1
jmquinn05
Member
 
Join Date: September 14, 2010
Location: The State of Texas
Posts: 23
M1 Garand Front Site

I have an M1 Garand that was my grandfathers and have cleaned it up nice the only problem i have found is the front site is a bit loose it moves from side to side and obviously will kill the accuracy. Any tips on fixing this without buying new barrel and gas tube?
jmquinn05 is offline  
Old October 16, 2010, 05:02 PM   #2
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,476
Take the sight blade out, and use a small hammer to lightly tap down the top of the dovetail notch to close it up a bit, then reinstall the sight. If the sight is still loose after tightening up the dovetail, you can use a center punch to make ONE punchmark in the center of the botton of the dovetail notch. If this still fails to tighten it sufficiently, try a drop of clear nailpolish or blue LocTite under the sight.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old October 16, 2010, 06:55 PM   #3
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 6,829
Scorch: That's not going to work on an M1 Rifle.

jmquinn05:
Is the sight loose on the gas cylinder, or is the gas cylinder loose on the barrel?

If the sight is loose on the gas cylinder, use the correct size Allen wrench to tighten the screw at the rear of the sight. If the screw is stripped, replace the sight and screw.

If the gas cylinder is loose on the barrel, a simple, easy, and non-destructive fix is to close the splines on the barrel slightly to tighten the fit of the gas cylinder.
Remove the gas cylinder lock screw, remove the gas cylinder lock, and remove the gas cylinder.

Lay a socket from a socket set on the top barrel spline where the splines on the gas cylinder fit.
Use a plastic screwdriver handle to give the socket a couple of raps.
Put the socket on the second spline and repeat.
Put the socket on the third spline and repeat.

This will slightly close the splines and tighten the fit of the gas cylinder.
This doesn't take much so don't hammer on the socket. The splines will close too much.
Ideally, you should have to put a small block of wood in front of the gas cylinder and gently tap the gas cylinder onto the barrel.
You don't want to have to drive it on, so that's why you should only tap the socket on the splines.

To reassemble the gas system, put the gas cylinder on the barrel, then screw the gas cylinder lock on until it touches the cylinder. Back the lock off until you can get the gas cylinder lock screw in, even if that takes almost a full turn of the lock.
When the screw is tightened, this will pull the gas cylinder and lock together.
Dfariswheel is offline  
Old October 16, 2010, 07:55 PM   #4
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,647
FWIW, I like to correct gas cylinder looseness by inserting a round bar into the top part of the cylinder and tapping it to spread the splines a bit. That has the same effect as closing up the spline cuts in the barrel and the cylinder is cheaper and easier to replace than the barrel if I go too far.

Jim
__________________
Jim K
James K is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06136 seconds with 7 queries