The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old October 16, 2010, 02:31 PM   #1
jmquinn05
Member
 
Join Date: September 14, 2010
Location: The State of Texas
Posts: 23
Finishing brass

I found a CVA 1861 Colt Navy that my dad got years ago and I just about have it done except for the brass and grip. I have the brass looking alot better than it did when I opened the kit but it still could use some work. I am out of ideas on what to use, this is the first kit I have built and the instructions for the gun are long gone. If anyone has any ideas that would be great. Thanks.
jmquinn05 is offline  
Old October 16, 2010, 03:33 PM   #2
bedbugbilly
Senior Member
 
Join Date: November 19, 2009
Posts: 2,319
I'm assuming the brass is "as cast"? If so, staert with a fine mill file and smooth up the casting. Brass has a tendency to "clog" the teeth of the file which can cause even more "scratches" - one way around this is to run a piece of chalk over the file before filing and repeat as necessary. From there, various grades of emery paper can be used. Back the emery paper with a small wood block or similar so that surfaces remane flat and square where they need to be. Once you have it worked down with the emery paper - say perhaps a 400 or 600 grit, you can then do a final buffing of it with a buffing wheel mounted on a grinder utilizing rouge. Just take it slow and don't over file, emery paper or buff in order to keep square edges square, etc. It sounds like you have a fun project - good luck with it! Others on here will probably have other suggestions as well as there is always more than one way to "get 'er done".
__________________
If a pair of '51 Navies were good enough for Billy Hickok, then a single Navy on my right hip is good enough for me . . . besides . . . I'm probably only half as good as he was anyways. Hiram's Rangers Badge #63
bedbugbilly is offline  
Old October 16, 2010, 03:44 PM   #3
jmquinn05
Member
 
Join Date: September 14, 2010
Location: The State of Texas
Posts: 23
It has been very fun working on it and I'm almost sad that its nearing the end but the result will be worth it. Thd steel was rusted from years of being in a shed but with some work it now has the look of an old gun. Thanks for the tips they will help out alot.
__________________
"Running around like a bunch of chickens with their legs cut off." - Uncle Si
jmquinn05 is offline  
Old October 16, 2010, 04:57 PM   #4
whipper
Member
 
Join Date: March 3, 2006
Posts: 46
Most all of my BP guns were kits, I had a lot of fun putting them together, a lot of filing and sanding.

If you have a dremal tool you can use it to get into the small areas for sanding and polishing.

I use Flitz to polish all the brass, with very little effort it will look like gold when done.

Have fun!
whipper is offline  
Old October 16, 2010, 05:48 PM   #5
Doc Hoy
Senior Member
 
Join Date: October 24, 2008
Location: Chesapeake, VA
Posts: 4,629
JM,

Once you get the finish where you want it you can hit it with Brasso or Neverdull. It'll shine like a ruby in a goat's a __ __.
__________________
Doc

My reading of history convinces me that most bad government results from too much government. Thomas Jefferson
Doc Hoy is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:30 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07306 seconds with 7 queries