The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting > Bullet Casting

Reply
 
Thread Tools
Old October 14, 2010, 06:01 AM   #1
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,922
Drive Band Fillout ????

These 2 bullets were cast at the same time from a lyman 314299 mold .All was up to temp , these long 30 cal. bullets warm up the mold qwik even though I prewarm on a hot plate !!!

The temp was 725f-750f in my bottom pour 10# lee.

The alloy was Isotope 94 /3/3 & I was castin fairly fast & I put big puddles on the sprue plate.

Is this cavity too hot & causing cook off of impurities in the alloy ????

Mold just too hot in general ???

Letting the mold cool & turnin down the temp is the only fix , but why not both cavitys ???

Am I answering my own question ????

__________________
GP100man
GP100man is offline  
Old October 14, 2010, 07:23 AM   #2
reloader28
Senior Member
 
Join Date: October 13, 2009
Location: nw wyoming
Posts: 929
Didnt I just see this??? Says its a new post.

I'm having the same problem with my new RCBS 180 30. I slowed my casting WAY down and dropped the temp down.
Seemed to fix the problem, but I'm going slow enough now that it @#$%es me off. I dont like casting slow.

Another way is to touch a damp rag to the outside of the mold where its getting hot for just a second. Cools it down fast. I use it quite a bit with a couple molds, but this one seems to heat up faster than most.

I'm thinking of cleaning the mold again in case theres something in there.
I also thought it might be cause its a new mold and not seasoned yet.

I was hoping someone would give you the answer so I would know.

Last edited by reloader28; October 14, 2010 at 07:35 AM.
reloader28 is offline  
Old October 14, 2010, 08:18 AM   #3
snuffy
Senior Member
 
Join Date: May 20, 2001
Location: Oshkosh wi.
Posts: 2,772
Quote:
Didn't I just see this??? Says its a new post.
I thought the same thing, then realized I saw it over on castboolits forum.

I had a 2 cav lee in .458 that did that in the same spot every time. Never did figure out whAt it was, I just used a bottom pour ladle like the Lyman to pressure cast. That took care of it, but man is it S-L-O-W----!!!.

IIRC it was a hollow point 405 grain .458. Never could get it to shoot, so it's on the back shelf gathering dust.
__________________
The more people I meet, the more I love my dog

They're going to get their butts kicked over there this election. How come people can't spell and use words correctly?
snuffy is offline  
Old October 14, 2010, 03:01 PM   #4
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,922
reloader28

It is a fairly new mold but I run it thru some heat cycles with the hot plate.


LOL !!!

I posted it over here also !

Shakin all the bushes !!!


I have a couple of idees to try , first is checkin the vent lines , second alternate pourin the cavitys first , preheat mold more & run the melt at 650f.

My 700 will chamber em sized 314 (actually there 313) & spits em out in 1 place , IF I do my part !!!!


The bout with the gout is almost over !!! lft knee feels like the cartilidge is gone though !!!

CRANBERRYS & ALEEVE , better than anything I tried !!!
__________________
GP100man

Last edited by GP100man; October 14, 2010 at 03:09 PM.
GP100man is offline  
Old October 14, 2010, 10:47 PM   #5
TXGunNut
Senior Member
 
Join Date: January 16, 2010
Location: If you have to ask...
Posts: 2,851
Glad to hear you're feeling better. Keep us posted on the boolits, casting for my .30-30 still on my project list.
__________________
Life Member NRA, TSRA
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call Lonesome Dove
My favorite recipes start out with a handful of used wheelweights.
TXGunNut is offline  
Old October 15, 2010, 05:54 AM   #6
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,922
Well TGN since ya mentioned the 30-30 I`ve come up with a way to maintain length on these old IDEAL 311314s to put a flat point on em so I can load em in a tube & another plus is the oglive grows .0015 also !!

__________________
GP100man
GP100man is offline  
Old October 15, 2010, 07:27 AM   #7
reloader28
Senior Member
 
Join Date: October 13, 2009
Location: nw wyoming
Posts: 929
As I was getting out of bed this morning, a thought hit me. It is rare, but once in a while.

Has anyone ever tried drilling a couple or 3 or 4 holes thru a mold for faster cooling?

I think, on molds like this that run very hot, it might keep it cooled down enough to work.

The more I think about it, the better it sounds. I'm sure tempted to try it.

Maybe 3 or 6 holes total - 1 or 2 on each side of the boolit cavities.
reloader28 is offline  
Old October 15, 2010, 04:02 PM   #8
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,922
I`ve seen molds that have been hollowed out on the underside for qwiker coolin , but they`d have to heat up faster also !!
__________________
GP100man
GP100man is offline  
Old October 15, 2010, 07:39 PM   #9
reloader28
Senior Member
 
Join Date: October 13, 2009
Location: nw wyoming
Posts: 929
I was thinking more of holes drilled the opposite direction of the cavities. Thru both mold halves sideways. Make like an air tunnel. Or maybe work like a sideways chimney.
reloader28 is offline  
Old October 15, 2010, 08:49 PM   #10
salvadore
Senior Member
 
Join Date: January 1, 2007
Location: Idaho
Posts: 1,845
GP, did you flatten the point in the lubersizer with a flat top punch, or what?
salvadore is offline  
Old October 15, 2010, 09:08 PM   #11
TXGunNut
Senior Member
 
Join Date: January 16, 2010
Location: If you have to ask...
Posts: 2,851
OK, GP, I'll bite. Looks like a different boolit but must admit I have no idea.
__________________
Life Member NRA, TSRA
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call Lonesome Dove
My favorite recipes start out with a handful of used wheelweights.
TXGunNut is offline  
Old October 16, 2010, 10:47 AM   #12
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,922
OK fellers I have it worked out !!!!

Cast the 311314 then GC em (I GC then size in seperate ops.) size em 314 ,apply lube . toppunch #467 I think.

The install 310 H&I die (my marlin won`t chamber anything bigger than .3105)
install TP 421 (I set the depth with the bullet in the pic) by adjusting the bullet depth screw to where the 421TP bumps the outer rim of the die.

I go slow to make shore da bullet is going in the 310 sizer straight , this is not a hi volume operation !!!!

Time to load & shoot some !!!! Gonna try min load of 3031 & a Wolf large rifle primer ????
__________________
GP100man
GP100man is offline  
Old October 16, 2010, 07:18 PM   #13
TXGunNut
Senior Member
 
Join Date: January 16, 2010
Location: If you have to ask...
Posts: 2,851
How'd it go, GP100man?
__________________
Life Member NRA, TSRA
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call Lonesome Dove
My favorite recipes start out with a handful of used wheelweights.
TXGunNut is offline  
Old October 16, 2010, 09:29 PM   #14
reloader28
Senior Member
 
Join Date: October 13, 2009
Location: nw wyoming
Posts: 929
I had better luck sizing to the size I wanted and finishing it ready to shoot, then flat nose them. Otherwise I was putting to much pressure on it (I think). Some came out crooked. I want it straight and fully into the die before the pressure flattens it.

Hope it works out and your happy with it.
reloader28 is offline  
Old October 17, 2010, 06:17 AM   #15
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,922
It went good !!!

I did`nt put as much as the 1 in the pic , but enuff I can load em in a tube & they`ll go thru the action of the 336

Just gotta steal time to load some , season opens tomorrow !!!!!
__________________
GP100man
GP100man is offline  
Old October 17, 2010, 08:36 AM   #16
TXGunNut
Senior Member
 
Join Date: January 16, 2010
Location: If you have to ask...
Posts: 2,851
Just so I'm clear, you're using a sizer and punch to swage a spitzer into a roundnose, GP100man? Cool idea!
__________________
Life Member NRA, TSRA
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call Lonesome Dove
My favorite recipes start out with a handful of used wheelweights.
TXGunNut is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09934 seconds with 7 queries