The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools
Old October 9, 2010, 06:15 PM   #1
Crazy Jack
Junior Member
 
Join Date: October 9, 2010
Location: Kickin Liberal and Communist Asses in Beautiful Downtown Marietta, Georgia
Posts: 1
Pre-Model 25-5?

Hi Folks! I’m new to this Forum, have a bunch of guns, and am retired LE. I am now a SCUBA Equipment Repair Tech (retired job) and one of those Idiot-Brained Casual Shooter Cave Divers.

I am curious to know as much as I can about this gun that I just acquired. I was in the process putting together the info for a Letter of Authenticity to S&W when I found all y’all. Please weigh in and tell me if I’m wrong on anything as well any other info that you would like to share, including what YOU would pay for it. Here goes:

My basic research on this gun tells me that it appears to be a Smith & Wesson 1955 Target Model (Heavy Barrel), Pre-Model 25 revolver. Caliber is .45 Colt, double action, 6 shot built on the square butt N frame with five screws and has a 4” pinned barrel. I think that these were originally produced with a 6 ½” barrel? and I do not know when this one was changed. But, as you can see, it is a Smith & Wesson barrel. On the left side of the barrel is “SMITH and WESSON”; Right side is: “45 Cal. Model 1955.” It has a target hammer and target trigger. It has what appears to be the circa 1970’s S&W orange insert front sight and a micrometer click rear sight. The serial number on the frame under the grips is “S79xxx.” I can’t make out any stamping info on the grips. It has the following on the cylinder swing ”KO 2498” (is that an Assembly Number?) and there is no Model Number stamped. It has a six-groove backstrap and checkering on the top ramp. It has what I would call a matt finish; i.e. it’s not blued, stainless, or nickel. It has no box or papers.

What’s the story on this baby?

Please see pictures below.

Crazy Jumpin Jack

Overall Left Side.jpg

Overall Back.jpg

Barrel Front Right.jpg
__________________
Crazy Jumpin Jack (Gregory)
jjgregory@mindspring.com
"Boys, the War Ain't Over Yet...We Just be a Waitin for Supplies"
http://www.diveshop1.com/stores/marietta/crew.php
Crazy Jack is offline  
Old October 10, 2010, 09:01 AM   #2
Ronbo1
Senior Member
 
Join Date: October 14, 2004
Location: MN
Posts: 135
Smith

I have a 25-2 1955 target model in original condition, the barrel is longer than 4 inches though. I think it is 6 1/2 inch, the caliber is 45 acp made to use 45 acp with moon clips or 45 auto brass with rim ammuntion. I wonder if this handgun had the barrel changed and shortened to 4 inch. It could of started out as a pre model 25 in 45 LC (long colt) and had the shortened 1955 barrel added. Is it matte (sand blasted) nickel finish?

Welcome to the forum
__________________
When the people fear the government, there is tyranny. When the government fears the people, there is liberty. America will never be destroyed from the outside. If we falter and lose our freedoms, it will be because we destroyed ourselves

Abraham Lincoln
Ronbo1 is offline  
Old October 10, 2010, 09:32 AM   #3
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 11,086
The 1955 barrel has been sawn off, you can see that the roll marks are not centered as they are applied at the factory.
The butt has been rounded and the grips reshaped to match.
The gun has been matte finished and nickel or chrome plated.

A factory letter will show the ORIGINAL configuration. But this ain't it.

A picture of the transition from topstrap to barrel rib would be helpful.

Lack of a model number means it was made before 1957, back when S&Ws had names, not numbers.

Edit: The thread on S&W board marks your gun as a .357 (pre-Model 27) rebarrelled and rechambered to .45, grip shape altered and refinished. A friend here had three guns converted. He found two tapered 1950 .45 (M26) barrels and one heavy 1955 and put them on .357 frames with the cylinders rechambered by Bob Snapp.

Last edited by Jim Watson; October 10, 2010 at 05:24 PM. Reason: Saw your thread on S&W board
Jim Watson is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:18 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06631 seconds with 10 queries