The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old September 23, 2010, 08:52 PM   #1
mrappe
Senior Member
 
Join Date: January 29, 2009
Location: Texas
Posts: 216
Just got my Lee ball mold today

The Lee instructions say to lubricate the v ribs but I am not sure what they are. Also it said to put carbon on the cavity with a match. Do you do this every time before you start?
mrappe is offline  
Old September 23, 2010, 08:58 PM   #2
Andy Griffith
Senior Member
 
Join Date: May 14, 2009
Location: Macon Co. NC
Posts: 569
The "V" ribs is the little piece of steel and the channel in the mould that help to locate and line up the mould halves correctly.

As for using the smoke from a match, I've never had to do it after the first time, unless a mould didn't want to release bullets well.

It's the smoke from a blown out match that you want to coat the mould with- not the flame- the carbon in very, very fine particulates.
__________________
Barney Fife: "Nip it, nip it, nip it!"
Andy Griffith:"Oh now Barn'...."
Andy Griffith is offline  
Old September 23, 2010, 09:06 PM   #3
mrappe
Senior Member
 
Join Date: January 29, 2009
Location: Texas
Posts: 216
What do you use to lube the mold? I don't have any bullet lube.
mrappe is offline  
Old September 23, 2010, 09:12 PM   #4
CameronP
Member
 
Join Date: August 25, 2010
Location: West Jordan, Utah
Posts: 54
Try using Rapine Graphite Mold Prep. works very well on my Lee molds
CameronP is offline  
Old September 23, 2010, 10:00 PM   #5
the rifleer
Senior Member
 
Join Date: March 5, 2008
Location: Sunny California
Posts: 1,257
I've never used lube and they come out pretty good. Let me give you a few tips that i learned the hard way. First, use gloves and protective clothing (shorts don't work well, ask me how I know haha).

Make sure your mold is hot. I hold mine over a propane torch for about 20 seconds which seems to work well. If the mold is too cold you will not get very good ball castings. Same if true if it is too hot. It just takes a little practice and a little patience. Use a dowel or something to knock it open and drop them onto a towel or even a bucket of water.

Be safe and have fun.
__________________
There is no such thing as a stupid question, only stupid people.
the rifleer is offline  
Old September 23, 2010, 11:59 PM   #6
CajunPowder
Junior member
 
Join Date: April 1, 2010
Location: Louisiana - Cajun Triangle
Posts: 223
Fascinating. +100
CajunPowder is offline  
Old September 24, 2010, 08:39 AM   #7
Noz
Senior Member
 
Join Date: February 25, 2009
Posts: 643
A candle will do in a pinch for a mold lube. The reason for the mold lube is that hot aluminum gets "sticky" and doesn't want to close or open easily.
Usually a one time smoking is all that is required.
You might wash the mold with acetone or lacquer thinner or strong alcohol before you smoke it.
Make sure that the lead, dead soft, that you are using is very clean. Multiple fluxings before you begin to cast. Dirty lead will eat the thin aluminum at the sprue away and give you a very ugly outcome. (Don't ask how I know and don't ask why it took a couple of ruined molds for me to figure that out
Noz is offline  
Old September 24, 2010, 12:44 PM   #8
Doc Hoy
Senior Member
 
Join Date: October 24, 2008
Location: Chesapeake, VA
Posts: 4,598
The way you smoke it.....

......is to hold it over a candle close to the wick. This serves to starve the flame of oxygen creating a carborizing flame which produces dark smoke and almost black soot. The black soot is the lubricant. Looks bad but it works.

You can also use talc which you can get from a pharmacist.

DO NOT USE CORN STARCH! It is too embarrassing.

I agree with whoever said, lubing it once lasts an awful long time. I schmootz mine up with talc about every three hundred balls.

As a disclaimer, I cast roundballs only and have absolutely zero experience casting other shaped bullets, although I do cast other things in lead.
__________________
Doc

My reading of history convinces me that most bad government results from too much government. Thomas Jefferson
Doc Hoy is offline  
Old September 24, 2010, 06:16 PM   #9
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 11,752
I've got prolly a dozen Lee molds and I never smoked any of them. I stick a corner in the lead to heat it up. I have one I bought used that was already smoked. Can't say I see any difference.
Hawg is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07320 seconds with 9 queries