The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old July 25, 2010, 03:50 PM   #1
Hoskins
Senior Member
 
Join Date: July 21, 2010
Posts: 240
A Few Gun Problems

Problem 1: Have a NEF 20 ga. Single Shot (break open) that sometimes will not fire a round, but dents the primer...though it is a light strick. I can put the same round in another 20 ga...an older Winchester single shot & it fires the round. Is this a firing pin, spring, or both problem? If so, can it be fixed by an ameture or gunsmith only?

Problem 2: 2 seperate shotguns, both .410 single shots & both will not eject a round when you break open the action. Is this an extractor problem? One of them is an old winchester model 38 & the other is a youth model Rossi.

Any and all help is much appreciated & thanks in advance for all who helps.
Hoskins is offline  
Old July 25, 2010, 04:26 PM   #2
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
Problem #1. Problem is: NEF Enuf said. Solution: wrap around a tree.
Problem #2. Just wondering, are they extractor models?
Rifleman1776 is offline  
Old July 25, 2010, 04:30 PM   #3
Bill DeShivs
Senior Member
 
Join Date: April 7, 2006
Posts: 7,129
NEF guns are extremely robust guns.
I would remove the firing pin and check for obvious signs of damage. Make sure the firing pin channel is totally clean and free of burrs. Oil the firing pin upon reinstallation.
__________________
Bill DeShivs
www.billdeshivs.com
Bill DeShivs is online now  
Old July 25, 2010, 04:56 PM   #4
Hoskins
Senior Member
 
Join Date: July 21, 2010
Posts: 240
Thanks gents...

Rifleman, if by extractor you mean it has an extractor at the bottom of the chamber, basically catches the end of the shotshell casing & pulls it out of the chamber...then yes they are. Please excuse my iggnorance. BTW, aint gonna wrap the NEF around a tree, too much sentimental value. I worked & saved up money for this gun while I was in 7th grade. I took my first squirrel, rabbit, & grouse with it! Though it was a dang funny comment & made me laugh!


Bill DeShivs, thanks for the advice. I haven't done what you said, but know that the firing pin does come all the way out & haven't seen any nicks or burrs on the tip of the firing pin. I will do as you say though. don't be suprised if I aint putting a 911 thread on here because I screwed it up!
Hoskins is offline  
Old July 25, 2010, 05:21 PM   #5
rtpzwms
Senior Member
 
Join Date: July 6, 2010
Location: OTS
Posts: 794
Problem 1 Clean and lube the whole shotgun. I had the same problem with a brand new Remmington SPR100. Ended up needing 3 good cleanings to get all of the cosmoline out of the gun. Until it was ALL gone I would see some dented primers without the round going off.
rtpzwms is offline  
Old July 25, 2010, 09:18 PM   #6
Goatwhiskers
Senior Member
 
Join Date: April 8, 2009
Location: Batchelor, La.
Posts: 472
On the assumption the the 20ga. is the more modern type with a transfer bar under the hammer, most misfires are caused by not firmly pulling the trigger ALL the way to the rear. The good old trigger "squeeze" causes the transfer bar to be out of position and gives the symptom of a light hammer strike. On the other two, could be weakness of the ejector spring, most likely the chamber needs a real thorough cleaning and honing to remove rust and deposits. Goatwhiskers the Elder
Goatwhiskers is offline  
Old July 25, 2010, 10:41 PM   #7
Hoskins
Senior Member
 
Join Date: July 21, 2010
Posts: 240
Thanks Goatwhiskers..."The Elder" You are correct, the 20 ga is modern & has th transfer bar. I'll test fire it & when it has a misfire, I pull the trigger a bit harder & see if that is the deal.

One detail I left out about one of the .410s. The Winchester .410 crimps the edge of the casing where the extractor/ejector is when you close the action.
Hoskins is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:25 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07183 seconds with 9 queries