The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old July 22, 2010, 05:48 PM   #1
Eskimo
Senior Member
 
Join Date: October 18, 2008
Posts: 173
Bullets for a .357 lever-action rifle?

I have a Marlin 1894SS, a Ruger SP101, and a Ruger Vaquero all in .357 mag.

I already have the powder and the primers, and now I'm looking to buy a bulk 1000 pack of bullets. Lever-actions can be a little temperamental with different types of ammo, and that's my main concern.

What type of bullet and what grain? I heard somewhere that you can't use full wadcutters in some revolvers. Are semi-wadcutters a good choice?

I will be using the lever for deer hunting (deep brush, 80 yards or less), so I would prefer 158 grain or higher.

Thanks in advance!
Eskimo is offline  
Old July 22, 2010, 06:09 PM   #2
zxcvbob
Senior Member
 
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,215
Best choice is a RNFP cast bullet, or a TC (truncated cone). SWC's usually won't feed well in a lever-action. You can also use JSP or JHP. 158, 160, 173, or 180 grains, take your choice.

148 grain DEWC's are probably OK in a .357 (they work in my Marlin) but will be too short when loaded in .38 Special cases.
__________________
"The only way to stop a bad guy with a gun is with a good guy with a gun"
zxcvbob is offline  
Old July 22, 2010, 06:28 PM   #3
Eskimo
Senior Member
 
Join Date: October 18, 2008
Posts: 173
Exactly what I was looking for, thanks!
Eskimo is offline  
Old July 22, 2010, 06:54 PM   #4
salvadore
Senior Member
 
Join Date: January 1, 2007
Location: Idaho
Posts: 1,910
I dont own a .357 rifle so i am probably talking out my pooper. I would go with a gascheck like Lyman's 358156 with gas check. My Marlin 94 with a gascheck bullet is a tackdriver
salvadore is offline  
Old July 22, 2010, 08:21 PM   #5
jmortimer
Junior member
 
Join Date: January 24, 2010
Location: South West Riverside County California
Posts: 2,763
Is this for hunting and self-defense? If so then a couple of these would be a great choice. Heat treated to 22 BHN and large meplat http://www.beartoothbullets.com/bulletselect/index.htm
If it's for punching paper there are better choices - i.e. less $$$ but for hunting or self-defense the are the best. Check the notes for the bullets that "feed through all lever actions."
jmortimer is offline  
Old July 22, 2010, 09:09 PM   #6
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 9,548
I shoot the same bullets in my Marlin 38/357 as I do in all my 38/357. That being 150 Cast SWCs (Lyman mold 358477). No problems encountered.
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School Oct '78
Distinguished Rifle Badge 1071
kraigwy is online now  
Old July 22, 2010, 11:46 PM   #7
housedad
Member
 
Join Date: February 6, 2009
Location: Southern NJ
Posts: 27
For my backpack carry, I have several 357 S&W and a couple of Marlin 1894's.

I got the 1894's jsut for the sake of being able to carry one cartridge with a rifle and a revolver.

I have handloads that put out 1450 fps muzzle on the revolver. If I go camping with that cartidge, I use 158gr JHP.

Lead, I have loaded and used Cast Round Nose or semiwads out of hardened wheel weights. Round nose feed better in the lever gun.

BTW, I have never had a decent feed in my levers with wadcutters.
housedad is offline  
Old July 23, 2010, 12:21 AM   #8
riverwalker76
Senior Member
 
Join Date: February 13, 2010
Location: Kentucky
Posts: 993
Before I starting casting my own lead I bought from Dardas Bullets at http://www.dardascastbullets.com. If I remember correctly I only paid around $57 for 1k .38 cal 158 gr. RNFP lead bullets. You can't hardly cast your own for that if you had to buy the same lead he uses.
__________________
Admiral Isoroku Yamamoto - “You cannot invade the mainland United States. There would be a rifle behind each blade of grass.”
riverwalker76 is offline  
Old July 25, 2010, 02:10 PM   #9
Clark
Senior Member
 
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 3,162
I know from shooting 45acp, 45Colt, and 44mag rifles, that a long bearing surface helps accuracy. That means heavy bullets.
Clark is online now  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:40 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08327 seconds with 7 queries