Glock 19 depressor / extractor problems

maxndale · April 17, 2010, 08:02 PM

I am having some problems with my Glock 19. I am getting about 5 Fail to extracts per magaizine. I have cleaned and recleaned and still getting the failures.

I took my 19 and my 22 apart and the only difference I can find is that the 19 doesnt have the spring loaded bearing in the end of the extractor depressor plunger spring that goes in the extractor depressor plunger

My question does the 19 have this little plastic bearing. Maybe I lost it in a prior cleaning?

I attached a photo of the G19 and G22 .

maxndale · April 17, 2010, 08:07 PM

The top one is out of the G22. Bottom G19 notice no cap in the end of the spring.

hoytinak · April 17, 2010, 08:08 PM

Yes, your G19 is supposed to have it.

rjrivero · April 17, 2010, 08:13 PM

The 9mm piece is black compared to the white 40 cal part. And YES, both should have one.

**JohnKSa** · April 17, 2010, 09:08 PM

You'll need to replace it and you'll need to know whether you have an LCI (Loaded Chamber Indicator) or non-LCI extractor in order to get the right one.

maxndale · April 17, 2010, 09:43 PM

thanks for the quick responses guys, would this be the casue of my Fail to Extracts. I sure hope so..

I have a newer G19 3rd gen. I beleive I have the chamber "loaded" indicator extractor.

**JohnKSa** · April 17, 2010, 09:49 PM

If the external surface of the extractor on the right side of the slide is flat then it's a non-LCI model. If it has a square bump at the forward end then it's an LCI model.

maxndale · April 17, 2010, 09:49 PM

best place to order Glock parts fast?

maxndale · April 17, 2010, 09:52 PM

yeap has the bump.

**JohnKSa** · April 17, 2010, 10:26 PM

Dunno that there's a big difference in where you order it from. OMB Express has always worked well for me but there are others that are good too.

maxndale · April 17, 2010, 10:41 PM

Thanks John for the help. I ordered one from MIDWAY.

dontbelieve · April 25, 2010, 02:15 PM

Glock parts dot com. I found them to be really fast for shipping.

April 17, 2010, 08:02 PM	#1
maxndale Member Join Date: January 24, 2010 Posts: 15	Glock 19 depressor / extractor problems I am having some problems with my Glock 19. I am getting about 5 Fail to extracts per magaizine. I have cleaned and recleaned and still getting the failures. I took my 19 and my 22 apart and the only difference I can find is that the 19 doesnt have the spring loaded bearing in the end of the extractor depressor plunger spring that goes in the extractor depressor plunger My question does the 19 have this little plastic bearing. Maybe I lost it in a prior cleaning? I attached a photo of the G19 and G22 .

April 17, 2010, 08:08 PM	#3
hoytinak Senior Member Join Date: July 5, 2006 Location: Texas Posts: 5,708	Yes, your G19 is supposed to have it. __________________ "Four wheels move the body. Two wheels move the soul."

April 17, 2010, 09:08 PM	#5
JohnKSa Staff Join Date: February 12, 2001 Location: DFW Area Posts: 16,771	You'll need to replace it and you'll need to know whether you have an LCI (Loaded Chamber Indicator) or non-LCI extractor in order to get the right one. __________________ Did you know that there is a TEXAS State Rifle Association? Check out Black Bear Flashlights.

April 17, 2010, 09:49 PM	#7
JohnKSa Staff Join Date: February 12, 2001 Location: DFW Area Posts: 16,771	If the external surface of the extractor on the right side of the slide is flat then it's a non-LCI model. If it has a square bump at the forward end then it's an LCI model. __________________ Did you know that there is a TEXAS State Rifle Association? Check out Black Bear Flashlights.

April 17, 2010, 10:26 PM	#10
JohnKSa Staff Join Date: February 12, 2001 Location: DFW Area Posts: 16,771	Dunno that there's a big difference in where you order it from. OMB Express has always worked well for me but there are others that are good too. __________________ Did you know that there is a TEXAS State Rifle Association? Check out Black Bear Flashlights.

April 17, 2010, 08:07 PM	#2
maxndale Member Join Date: January 24, 2010 Posts: 15	The top one is out of the G22. Bottom G19 notice no cap in the end of the spring.

April 17, 2010, 08:13 PM	#4
rjrivero Senior Member Join Date: November 17, 2008 Location: NW Ohio Posts: 1,321	The 9mm piece is black compared to the white 40 cal part. And YES, both should have one.

April 17, 2010, 09:43 PM	#6
maxndale Member Join Date: January 24, 2010 Posts: 15	thanks for the quick responses guys, would this be the casue of my Fail to Extracts. I sure hope so.. I have a newer G19 3rd gen. I beleive I have the chamber "loaded" indicator extractor.

April 17, 2010, 09:52 PM	#9
maxndale Member Join Date: January 24, 2010 Posts: 15	yeap has the bump.

April 17, 2010, 10:41 PM	#11
maxndale Member Join Date: January 24, 2010 Posts: 15	Thanks John for the help. I ordered one from MIDWAY.

April 25, 2010, 02:15 PM	#12
dontbelieve Junior Member Join Date: March 8, 2010 Location: West Central Florida Posts: 6	Glock parts dot com. I found them to be really fast for shipping. __________________ A day of freedom was bought with the blood of a patriot. Don't Tread on Me