Adjustable Combs

Dre · January 25, 2010, 04:47 PM

I was wondering if this is a good deal? also, what does plug stock mean?

Adjustable Combs
4-way Adjustable comb
$200
4-way Adjustable comb- Soft top
$285
Plug stock, when required
$50
Browning factory adj comb conversions
to Graco replacement hardware system
$150
Hard-top Adjustable comb conversion
to Soft-top
$85
Rebuild Soft-top
$70

mwar410 · January 25, 2010, 04:54 PM

" plug stock" if they cut into the bolt hole, and they need to plug the hole.

BigJimP · January 25, 2010, 07:33 PM

Where did you get the quote from DRE ?

Is it a reputable shop / somebody that has experience doing all these different options / is it close so you can go by the shop and check them out - or something off the internet ?

Dre · January 25, 2010, 08:03 PM

Where did you get the quote from DRE ?

Ken Rucker of Speedbump Stockworks

http://speedbumpstockworks.blogspot.com/

BigJimP · January 25, 2010, 08:14 PM

Ok, now I understand ....

I think you should start a new thread - and ask specifically for guys experience with speedbump ...

I've seen the name / but I've never sent a gun to them ....

Dre · January 25, 2010, 08:22 PM

BigJimP · January 25, 2010, 08:27 PM

For what its worth / his prices seem relatively cheap ....

Dre · January 25, 2010, 08:37 PM

He also installs recoil systems, here's one of them:

Ken Rucker's Bump-Buster (TM) With Pad Adjuster
Installed, including new Kickeez pad and
standard-duty hydraulic cylinder

Aluminum finish
$425

Here the video of his work:

http://www.youtube.com/watch?v=BFhRiSmopuM

January 25, 2010, 04:47 PM	#1
Dre Member Join Date: December 15, 2009 Location: Sacramento, CA Posts: 80	Adjustable Combs I was wondering if this is a good deal? also, what does plug stock mean? Adjustable Combs 4-way Adjustable comb $200 4-way Adjustable comb- Soft top $285 Plug stock, when required $50 Browning factory adj comb conversions to Graco replacement hardware system $150 Hard-top Adjustable comb conversion to Soft-top $85 Rebuild Soft-top $70

January 25, 2010, 08:22 PM	#6
Dre Member Join Date: December 15, 2009 Location: Sacramento, CA Posts: 80	Thanks Jim

January 25, 2010, 04:54 PM	#2
mwar410 Senior Member Join Date: December 25, 2008 Location: maine Posts: 234	" plug stock" if they cut into the bolt hole, and they need to plug the hole.

January 25, 2010, 07:33 PM	#3
BigJimP Senior Member Join Date: February 23, 2005 Posts: 9,963	Where did you get the quote from DRE ? Is it a reputable shop / somebody that has experience doing all these different options / is it close so you can go by the shop and check them out - or something off the internet ?

January 25, 2010, 08:03 PM	#4
Dre Member Join Date: December 15, 2009 Location: Sacramento, CA Posts: 80	Where did you get the quote from DRE ? Ken Rucker of Speedbump Stockworks http://speedbumpstockworks.blogspot.com/

January 25, 2010, 08:14 PM	#5
BigJimP Senior Member Join Date: February 23, 2005 Posts: 9,963	Ok, now I understand .... I think you should start a new thread - and ask specifically for guys experience with speedbump ... I've seen the name / but I've never sent a gun to them ....

January 25, 2010, 08:27 PM	#7
BigJimP Senior Member Join Date: February 23, 2005 Posts: 9,963	For what its worth / his prices seem relatively cheap ....

January 25, 2010, 08:37 PM	#8
Dre Member Join Date: December 15, 2009 Location: Sacramento, CA Posts: 80	He also installs recoil systems, here's one of them: Ken Rucker's Bump-Buster (TM) With Pad Adjuster Installed, including new Kickeez pad and standard-duty hydraulic cylinder Aluminum finish $425 Here the video of his work: http://www.youtube.com/watch?v=BFhRiSmopuM