The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old January 17, 2010, 06:49 PM   #1
brmfan
Senior Member
 
Join Date: October 21, 2008
Posts: 523
1 vs 2-piece scope mounts

For a hunting rifle that will most likely get bumped and banged around in hilly and rocky terrain, would there be any advantage with a 1 piece scope mount over a 2 piece? Specifically, I have a spare steel dovetail base that was used with an Accuracy International 1 piece mount (which I don't have anymore) and was considering getting a replacement mount and going with that setup since it seemed pretty solid.

My logic is that if the rifle were to get dropped or bang against a rock etc, the force would be spread out across the entire 1 piece mount as opposed to being focused directly on only 1 ring, thereby reducing a potential shift in zero. I had a buddy once loose a beautiful 8 point buck after dropping his rifle. He shot at it 3X at less than 150 yards and missed all 3 because his zero had shifted so much.
brmfan is offline  
Old January 17, 2010, 07:06 PM   #2
1911rocks
Senior Member
 
Join Date: September 9, 2006
Posts: 424
Close?

I exclusively use Armalite one piece mounts for just the reason you stated. They are essentially there own platform. I know that the Armalite's are a Picatinny format, but I believe it's applicable http://www.armalite.com/ItemForm.asp...9-bafe17a66e1e
1911rocks is offline  
Old January 17, 2010, 09:34 PM   #3
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 16,222
Rigidity is the way to go. One piece base.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old January 19, 2010, 03:10 AM   #4
sholling
Senior Member
 
Join Date: May 18, 1999
Location: Hemet (middle of nowhere) California
Posts: 4,254
Have you looked at DedNuz (aka DNZ) mounts?

__________________
Proud Life Member: National Rifle Association, California Rifle & Pistol Association, and the Second Amendment Foundation.
Annual Member: Revolutionary War Veterans Association (Project Appleseed) and the Madison Society.
sholling is offline  
Old January 19, 2010, 09:51 PM   #5
rudy270
Junior member
 
Join Date: January 18, 2010
Posts: 53
don't know

i use 2 peice because there easer to use an line up the rings, and if you drop your gun that hard even with a one peice the scope most likely going to get screw up
rudy270 is offline  
Old January 19, 2010, 10:12 PM   #6
Christchild
Senior Member
 
Join Date: June 19, 2009
Location: Loadbenchville, Bolt 02770
Posts: 537
My Browning A-Bolt wears an EGW Aluminum Picatinny 1-piece base. I chose that base because 1, it's aluminum which is weather resistance, and 2, 1-piece which is strength. I also originally bought the Burris Ex. Tac. Rings (again, aluminum and beefy) Medium height but they were at LEAST 1/4" too high as that combination left about 1/2" of clearance. My lady bought for me for Christmas the Burris Ex. Tac. Low rings which are perfect for my rifle/base/scope. Now I have about 1/4" of clearance between the objective and the barrel, minus a little bit for the scope cover.

In terms of strength + weather resistance, 1-piece, aluminum (if possible) and beefy. As others have posted, a hunting rifle takes a bit more abuse than rifles intended for mostly range/plinking use, so "extra" strength is definitely a plus. Integrity to Spare...
__________________
***If the Ignorant say to You, "The Soul dies like the Body", reply to them, "The Flower dies but the Seeds remain"...* That is a Law of God.
***Mighty Pleasant, don't You think...?
Christchild is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:42 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07560 seconds with 9 queries