The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting > Bullet Casting

Reply
 
Thread Tools
Old January 7, 2010, 07:02 PM   #1
Ed_
Member
 
Join Date: January 27, 2009
Location: Southwest Missouri
Posts: 96
Substitute Lube for Lee die

I waited all week for my shipment containing:
Lead pot, Sizer, Liquid alox , Thermometer & Bullet Mold

I open the box and start reading the Bullet mold instructions. It says:

"lubricate your mold. Very Lightly touch bullet lubricant to the spruce busing "V" ribs and locating cross pins. Use Lee Lube #90007. Do not use liquid Alox as it will bake onto the surface preventing proper closure."

Ok I am dead in the water... I only have Liquid Alox.

My question Is: Is there a substitute compound I can use to lube the mold.

Ed
Ed_ is offline  
Old January 7, 2010, 07:59 PM   #2
snuffy
Senior Member
 
Join Date: May 20, 2001
Location: Oshkosh wi.
Posts: 2,774
Yup! Any high temp grease or oil will do. If you have some anti seize that'll work, if it doesn't have those chunks of metal in it. Otherwise, very carefully melt some candle wax onto the locator pins and pivots. Take care to NOT let it get into the mold cavity, it will mess up your bullets until you get it out of there.

Best lube made for the locator pins and pivots on bullet molds is from the bull shop up in Alaska, it's called bull plate lube. It's a light blue oil that simply will not burn at casting temps. Here's the url for bull shop;

http://bullshop.gunloads.com/

If you order from them, be patient. They have a 10 mile long driveway to their mail box. They only go to town once a week, maybe less now that it's winter.

Bullplate is $4.00 a bottle, about 4.0 ounces. Now that's not much, but you use very little.
__________________
The more people I meet, the more I love my dog

They're going to get their butts kicked over there this election. How come people can't spell and use words correctly?
snuffy is offline  
Old January 7, 2010, 08:03 PM   #3
keebo52
Senior Member
 
Join Date: January 30, 2005
Posts: 244
+1 on the bull plate lube. It's the best stuff I've found for lubing molds.
keebo52 is offline  
Old January 7, 2010, 08:29 PM   #4
Ed_
Member
 
Join Date: January 27, 2009
Location: Southwest Missouri
Posts: 96
Thank you very much. I will order the Bull plate lube and see if I can get some anti sieze or High temp grease till the order comes in.

Ed
Ed_ is offline  
Old January 7, 2010, 08:36 PM   #5
IllinoisCoyoteHunter
Senior Member
 
Join Date: December 23, 2008
Location: Southern Illinois
Posts: 1,505
Bull plate is great stuff. FOLLOW the directions that come with it and you will never cast without it. Candle wax works too it you are in a pinch. But first be sure to get the mold hot, and try not to get the wax in the cavity...it is a pain in the @**. A little bit goes a long way. Good luck!
__________________
~~IllinoisCoyoteHunter~~

~NRA LIFE MEMBER~
~NRA CERTIFIED INSTRUCTOR~
IllinoisCoyoteHunter is offline  
Old January 8, 2010, 10:48 PM   #6
trip_sticker
Member
 
Join Date: August 28, 2009
Posts: 88
When I got my new mold from Lee, all I did to it was boil it in sopay water, then boil it in clean water, rinse it well and start casting with it. I got it hot, melted some candle wax on it, ( I got a bunch inside the cavity too) and burned that out in the first pour or two. I've never done anything to the mold since. I leave the last pour in it to cool and next time around, I just get it hot again and start pouring. Never had any trouble with the mold closing or anything. What is the lube supposed to do? I'm getting great looking bullets, they are all dropping at .359 or .360 (this from the Lee 90321 TL358-158-SWC)
trip_sticker is offline  
Old January 8, 2010, 11:35 PM   #7
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,922
Be careful with the bullplate & don`t knock over the bottle !!!

I take a Qtip & just rub the lid , then apply other wise I apply TOO much!!
__________________
GP100man
GP100man is offline  
Old January 9, 2010, 12:45 AM   #8
IllinoisCoyoteHunter
Senior Member
 
Join Date: December 23, 2008
Location: Southern Illinois
Posts: 1,505
Quote:
Be careful with the bullplate & don`t knock over the bottle !!!
Glad I am not the only one who has done that...
__________________
~~IllinoisCoyoteHunter~~

~NRA LIFE MEMBER~
~NRA CERTIFIED INSTRUCTOR~
IllinoisCoyoteHunter is offline  
Old January 10, 2010, 01:05 AM   #9
speedracer211
Senior Member
 
Join Date: April 30, 2007
Posts: 176
On my six cavity mould using anti-seize the bolt looks worn and I only cast about 500 rounds is that normal?
speedracer211 is offline  
Old January 10, 2010, 01:51 AM   #10
IllinoisCoyoteHunter
Senior Member
 
Join Date: December 23, 2008
Location: Southern Illinois
Posts: 1,505
500 and it is worn....that is not right. I have got thousands of bullets out of my Lee 6 cavs. Order ya some Bull Plate lube. It DEFINATELY extends the life of molds...NO DOUBT! Are you sure you didn't use a lapping compound?
__________________
~~IllinoisCoyoteHunter~~

~NRA LIFE MEMBER~
~NRA CERTIFIED INSTRUCTOR~
IllinoisCoyoteHunter is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:03 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08516 seconds with 9 queries