The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old December 5, 2009, 09:41 AM   #1
jtheise4
Member
 
Join Date: April 4, 2009
Posts: 26
installing Trijicon night sights on a S&W M&P

Does anyone have any experience installing Trijicon night sights on a Smith & Wesson M&P 9mm? The instructions that came with the sights are very incomplete at best and when I looked on their website, it recommends having them professionally installed. Before I spend the money to have a gunsmith install them, I was hoping to get some feedback regarding how difficult the instillation really is. Thanks.
jtheise4 is offline  
Old December 5, 2009, 10:01 AM   #2
jon_in_wv
Senior Member
 
Join Date: August 22, 2004
Posts: 664
I installed Ameriglo night sights in my M&P. I you can get your hands on a sight pusher that would be the ideal way to do it. Otherwise you can use a brass punch like I did. The factory front sight was in TIGHT. I had to hammer the HECK out of the front sight to get it out. To install the new sights they might be slightly over size. If it feels too tight then lay the bottom of it flat on a file and file a LITTLE bit at a time until it fits. Don't file the angles or you'll screw it up. Tap them in so they fit snug with your brass punch. The punch will make marks but its just brass transferring onto the steal. You can remove it with a little Hoppes #9.

Also if I'm not mistaken the dovetails are slightly tapered. Remove the old sights left-right (towars the ejection port) and install the opposite way.

Qualifier: I'm not a real smith so if someone smarter want to chime in and correct me go for it. Also, I believe that if you damage the tritium vials using a punch you will void the warranty.
__________________
Why has INTEGRITY become such a rare commodity?
jon_in_wv is offline  
Old December 5, 2009, 11:25 AM   #3
teeroux
Senior Member
 
Join Date: December 12, 2006
Posts: 1,491
^^^

The only thing I can add is if to file down the the bottom of the new sight I find it is easier to handle and do with a coarse diamond knife stone than handle it on a file. Remember they come on and off the right side of the firearm.
teeroux is offline  
Old December 5, 2009, 12:18 PM   #4
sholling
Senior Member
 
Join Date: May 18, 1999
Location: Hemet (middle of nowhere) California
Posts: 4,258
They only go in one way but unless you have a sight pusher you're probably going to screw up your finish. Even with a sight pusher it's a pain because they often need fitting. I highly recommend paying the local smith $20-40 to put them on.

BTW if memory serves there is a spring and plunger held in place by the rear sight and if you aren't careful you'll be crawling around looking for it.
__________________
Proud Life Member: National Rifle Association, California Rifle & Pistol Association, and the Second Amendment Foundation.
Annual Member: Revolutionary War Veterans Association (Project Appleseed) and the Madison Society.
sholling is offline  
Old December 8, 2009, 08:01 PM   #5
jon_in_wv
Senior Member
 
Join Date: August 22, 2004
Posts: 664
I disagree. a brass punch is soft and NOWHERE near the hardness of the slide or the melonite finish. Any marks you leave will be the brass transferring on to the slide and that is easily cleaned off. The only real danger is hammering too hard on the sight causing it to peen or actually damaging one or the tritium vials. I've changed my rear sight three times and front sight twice with a brass punch and the finish is still like new. Believe me, the first time I tried to remove the factory front sight it needed more than a little persuasion to get it out. It was SUPER tight.

I've also used a brass punch on my FEG HiPower with its fine bluing and softer metal with good results also. I do agree with you that if you have a smith locally that is CERTIFIED to do the work with those sights I would let him do it to protest your warranty. If he isn't, I would say you probably have as good a chance as getting it right yourself. I've had bad luck with smiths installing sights on my weapons.
__________________
Why has INTEGRITY become such a rare commodity?
jon_in_wv is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:06 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06790 seconds with 7 queries