The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Curios and Relics

Reply
 
Thread Tools
Old November 7, 2009, 09:31 PM   #1
essohbe
Junior member
 
Join Date: March 22, 2009
Location: U.S.A.
Posts: 817
Refinishing a Mosin

Haven't done this yet, will be a winter time project.

Does anyone have any reccommendations for stripping off shellac and finish?

I figured denatured alcohol, then something to pull the stain out but maybe I could match the color and go right over the old stuff?
essohbe is offline  
Old November 7, 2009, 10:07 PM   #2
Joker0370
Member
 
Join Date: August 24, 2009
Location: Philadelphia, PA
Posts: 19
I got a junked one for free and put it back together, and this included refinishing the stock. First things first: Its not something rare and un-replacable is it? I know the idea that "its a mosin and they are 80 bucks" floats around but it might be good to make sure. Assuming you gone one for free that is missing a lot of stuff or looks like the dog has chewed on it, the best thing for stripping a solid wood stock for me was oven cleaner. Stripped the wood down bare in minutes. The longest and hardest part was letting it dry back out. I did some searching and found a website on using tung oil to refinish gun stocks (i think its called flowers of the tung http://www.surplusrifle.com/shooting...df/tungoil.pdf) and followed that. Came out very nice. I didn't quite qet the color i wanted on the first try, so i'd recommend testing out some stains on scrap wood to get the best color. If i were to do it again, i'd use the Sedona Red stain (nice red tint).

I think it took me about 2 weeks from start to finish, working on and off. Lots of drying time between coats.
Joker0370 is offline  
Old November 7, 2009, 10:53 PM   #3
mp25ds4
Senior Member
 
Join Date: March 6, 2009
Posts: 392
you shouldnt refinish a junked mosin that hasnt already been refirbished, the non-referbished ones are getting harder and harder to find
__________________
Liberal Newscaster Katie Couric, while interviewing a Marine sniper, asked:
'What do you feel.....when you shoot a Terrorist?'
The Marine shrugged and replied, "A Slight Recoil."
mp25ds4 is offline  
Old November 7, 2009, 11:02 PM   #4
Swampghost
Senior Member
 
Join Date: April 18, 2008
Location: Florida, east coast
Posts: 2,106
As said, original cond. is best value and I wouldn't mess with it.

If you're determined to refinish, it's a process if you want decent results. I'm a woodworker that specializes in fine cabinetry and yacht finishes among other things.
__________________
NRA Patron Member
Swampghost is offline  
Old November 24, 2009, 07:04 PM   #5
MagnumWill
Senior Member
 
Join Date: March 18, 2009
Location: Central Colorado
Posts: 698
It all depends on what you want to do. Sure, you may "wreck" the value of the stock (that's probably mismatched anyway) but keep in mind that its still a 90 dollar rifle. Do what you want with it- I refinished my M44 stock twice. I stripped off the shellac with (get this) a razor blade. It flew right off, and I stained it. Didn't like it, so I sanded it down to the wood underneath (which looks great) and I just put the oil coat on it, and I love it. Here, I'll put a pic of it up. The Mosin PU sniper has the original shellac on it. The Tula hex has a laminate stock on it that was beautiful to begin with when I got it.

__________________
Generally speaking holes in anti-gun theories are called "facts."
-Madcap_Magician
MagnumWill is offline  
Old November 24, 2009, 09:36 PM   #6
FALPhil
Senior Member
 
Join Date: September 10, 2007
Location: Racoon City
Posts: 933
I recommend a commercial stripper, like Strip-eze. Denatured alcohol takes too long and the result is the same. I even used EZ Off oven cleaner on one and it worked great.

After the shellac was stripped, I washed the stock down with a solution of dishwasher powder and water. Then I rinsed it well and let the stock dry out for two weeks in a 50% humidity environment (my gun room where I keep a dehumidifier). Then, I set about refinishing the stock. I sanded lightly, and then used a 50-50 mix of tung oil and mineral spirits for the first coat. Subsequent coats were 75% tung. The result was a durable finish that looked like new shellac.

If you use a stain, be sure to use an oil based stain, as water based stains are hard to keep from blotching.
FALPhil is offline  
Old November 25, 2009, 12:28 AM   #7
mp25ds4
Senior Member
 
Join Date: March 6, 2009
Posts: 392
is this mosin a non refurb? if so i wouldnt refinish it
__________________
Liberal Newscaster Katie Couric, while interviewing a Marine sniper, asked:
'What do you feel.....when you shoot a Terrorist?'
The Marine shrugged and replied, "A Slight Recoil."
mp25ds4 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:45 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07221 seconds with 7 queries