The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old September 26, 2009, 05:20 PM   #1
bluebox
Junior Member
 
Join Date: September 26, 2009
Posts: 2
Knoxx Specops 870 help

Help!

I just purchased a Knoxx Specops stock for a 870 but I'm having a hard time installing it. The metal screw only goes in 1/8 of the way in, if that. Its very difficult to screw in, almost feels as if the bolt is larger. In either case I'm afraid of damaging the threads. Is there something I'm missing? I couldn't find where anyone else had any trouble installing this? Seems very easy and straight foward.
bluebox is offline  
Old September 26, 2009, 09:30 PM   #2
Technosavant
Senior Member
 
Join Date: May 29, 2007
Location: St. Louis, MO area
Posts: 3,913
It's just something that takes some effort to screw in. Make sure the hole and screw threads are clean. Then, before beginning to tighten anything as you mate them together, "unscrew" (yeah, it isn't actually screwed in yet, but work with me here) the screw until you feel the threads bump- that's the things lining up so you won't crossthread it. Then, just tighten it; I think I eventually had to use pliers on the short leg of the allen wrench. You'll know when it's done being obstinate and is actually tight.
Technosavant is offline  
Old September 27, 2009, 09:13 PM   #3
bluebox
Junior Member
 
Join Date: September 26, 2009
Posts: 2
Do all 870's use the same bolt? I just purchased my Remington a month ago, maybe something changed? just seems like I wont be able to remove it ever again if i use that much force.
bluebox is offline  
Old September 27, 2009, 09:19 PM   #4
hogdogs
Staff In Memoriam
 
Join Date: October 31, 2007
Location: Western Florida panhandle
Posts: 11,069
Take the bolt out of the stock and try threading it... Then, if it went, look closely at your angle and try again. Compare the 2 bolts and if the same length use the original. Also verify the threads are same pitch and width.
Brent
hogdogs is offline  
Old September 28, 2009, 10:37 PM   #5
Shpadoinkel
Member
 
Join Date: August 14, 2009
Posts: 19
I assume you took out the metal spacer as instructed?

I put an 870 Knoxx on my Pardner Protector (870 clone). Installation took all of 5 minutes and fit like a glove, no threading issues whatsoever. I'd be amazed if the stock fit better on a clone gun than on the gun that it was actually intended for.

Only thing I could think is you didn't remove the metal spacer. If you have... I don't know what's going on.
You shouldn't have to force it at all. If you're hitting more resistance than you think necessary, something is up. I seriously doubt the newer 870's are using a different bolt.
Shpadoinkel is offline  
Reply

Tags
870 , knoxx

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:01 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06523 seconds with 7 queries