The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old August 16, 2009, 03:45 PM   #1
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,242
Removing bluing

I need to remove the bluing from an old S&W revolver. A lot of it is gone, but I'd like to finish the job and reblue it.

What products are there on the market for this?

I know I can use Birchwood Casey Blue & Rust remover, but it's hard to find, harsh as all get out, and expensive.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old August 16, 2009, 04:17 PM   #2
Bill DeShivs
Senior Member
 
Join Date: April 7, 2006
Posts: 7,166
Muriatic acid, for 10-30 seconds.
__________________
Bill DeShivs
www.billdeshivs.com
Bill DeShivs is offline  
Old August 16, 2009, 05:24 PM   #3
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,242
Where the hell do I get muriatic acid?

How do I apply it?

What strength?
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old August 16, 2009, 05:41 PM   #4
johnbt
Senior Member
 
Join Date: December 6, 1999
Location: Richmond, Virginia USA
Posts: 6,004
At the hardware store, it's brick cleaner or toilet bowl cleaner. Ask them where the smallest package is, you don't want the gallon size I guess.

And it's hydrochloric acid - about 30% I think - so use it outside, rinse really well, oil the gun immediately.

I've read of folks using it indoors to clean tile floors and having the vapor discolor every stainless steel appliance in the room.


Have you tried a lead away cloth or maybe blood. I hear that works.

John

edited to add: The directions for cleaning brick is to water it down something like 10- or 20 to 1, but read the instructions. If I was going to use it I think I'd mix a weak solution in a plastic bucket, dunk the gun and then either dunk it in a bucket of clean water or hose it off two or three times. Repeat as necessary. And then dunk it in oil.
johnbt is offline  
Old August 16, 2009, 05:57 PM   #5
Bill DeShivs
Senior Member
 
Join Date: April 7, 2006
Posts: 7,166
I believe it's also sold in pool supplies.
Use it full strength. Pour it into a plastic container and drop the parts into it. Neutralize it in water with ammonia or baking soda added. Use rubber gloves and eye protection. Regular surgical gloves will not be affected by the acid, and they let you handle the parts. Don't breathe the fumes.
Only leave the gun in long enough to remove the bluing! Check it often.
After rinse, flood parts with WD 40.
When finished, use a plastic funnel and pour it back in the original container for later use.
__________________
Bill DeShivs
www.billdeshivs.com
Bill DeShivs is offline  
Old August 16, 2009, 06:45 PM   #6
Walt Sherrill
Senior Member
 
Join Date: February 15, 1999
Location: Winston-Salem, NC USA
Posts: 4,520
I've used the Birchwood-Casey Rust and Bluing Remover (a fluid) and found it did the job well. (It's the only Birchwood-Casey product I can recommend.) You've find it at gunshops and places that sell cold bluing, cleaning supplies for guns, etc. I saw some in a gun shop, recently.

The last time I bought a bottle, it was like $5, but that was sevearl years ago. It doesn't take much.
Walt Sherrill is offline  
Old August 16, 2009, 07:47 PM   #7
BillCA
Senior Member
 
Join Date: November 28, 2004
Location: Silicon Valley, Ca
Posts: 7,087
Mike,

Try the folks at Brownell's.com - you're looking for their Steel White rust remover #082-055-032 in a quart bottle. Dilute it according to directions (about 5:1 with pure water) and immerse the gun. You'll need to wear gloves and eye protection is recommended. This product works well for removing old bluing.

After dunking, you'll need a good degreasing/cleaning product to remove all traces of the chemical. They recommend Dicro-Clean 909 (#082-005-008), but for a single gun a can or two of brake cleaner will likely do the job.

I'd recommend against muriatic acid or as it is correctly called hydrochloric acid. This acid can attack metal if left too long. And you need to know the strength of the acid so you can properly dilute it, something that's often missing on the acid sold for swimming pool use (generally a 10%-12% solution). Concentrated acid will fume if it is above about 32% and breathing equipment is needed.
__________________
BillCA in CA (Unfortunately)
BillCA is offline  
Old August 16, 2009, 08:43 PM   #8
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,837
That Rust and Blue Remover IS muriatic acid. It does a good job, but do several appllications rather than leaving it on too long as it will frost the steel.

Incidentally, for those who think factories apply a "mirror finish" polish, using blue remover is an education in how much roughness hot salt bluing can cover up. And why gunsmiths who try for a "mirror finish" are never able to duplicate the factory finish.

Jim
__________________
Jim K
James K is offline  
Old August 17, 2009, 12:19 AM   #9
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,242
Excellent information. Thanks, all.

The gun I want to reblue is an M&P in .32-20. The finish is probably only about 50%, it's got a fair amount of pitting, and a bunch of nicks and scars.

The bigger problem, one that I've yet to solve, is that it's almost impossible to thumb cock for single action. It locks up. But pulling the trigger for double action works, although it is rough and hitchy.

I think the cylinder bolt is the culprit, but I've not had a chance to thoroughly investigate it yet.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old August 17, 2009, 06:38 AM   #10
BillCA
Senior Member
 
Join Date: November 28, 2004
Location: Silicon Valley, Ca
Posts: 7,087
Mike,

Use a jeweler's loupe and inspect the star extractor palls where the hand engages. Look for a small gouge in the surface or some rough spot or burr. Also check the nose of the hand to make sure it's not burred.

I'd double check the pin(s) in the hand to make sure they're not worn loose, as well as the hammer and trigger studs.

I'm betting on a worn or pitted extractor pall. Especially if some chambers work smoother than others.
__________________
BillCA in CA (Unfortunately)
BillCA is offline  
Old August 17, 2009, 10:16 AM   #11
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,242
The pawls are fine.

The hand is fine.

It still does it even with the hand removed.

The studs are all straight.

The problem seems to be the interaction between the trigger nose and the cylinder bolt.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old August 17, 2009, 11:43 AM   #12
jglenn
Member
 
Join Date: May 22, 2009
Location: Georgia
Posts: 51
rust removal

Evapo - rust


works very well and will coat the part after you remove it so it won't rust for a day or so. Tried Brownell's new rust remover but it doesn't work as well.
jglenn is offline  
Old August 17, 2009, 03:33 PM   #13
George R
Senior Member
 
Join Date: December 17, 2004
Location: Boca Raton, FL
Posts: 151
Blue Remover

I agree with JGlenn. Evap-O-Rust is the best. I buy it by the 5 gal bucket, but you can get small quantities at an auto parts store. You can leave the gun in it for a prolonged period of time and not have to worry. Muriatic (swimming pool) acid can pit the hell out of your gun in seconds.
George R is offline  
Old August 17, 2009, 05:46 PM   #14
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,242
So Evap-O-Rust will remove bluing and prepare the surface for new bluing?
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old August 17, 2009, 07:44 PM   #15
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,406
Evaporust is a chelating compound and works very well. So does a competing product called Rust Release. I have tried both and the latter has a slightly lower pH and works faster. Neither is something you want to leave steel in too long. Figure 15 minutes or so. I've used these on red rust, and if you have any, it will get rid of it. It will, however, leave the surface slightly matte after longer exposure I think all the finish removers will if you leave things in them long enough. It's not a bad surface if you are going to rust blue it later. If you leave something in either brand long enough a black surface coating appears that has to be rubbed off. But I agree it is good for attacking any kind of iron oxide, the magnetite that constitutes bluing, included.

Another product that is quite good is Iosso Quick Strip. It will take off bluing or Parkerizing and is pretty easy on the steel. It is designed specifically for this job. I've used it to strip Garand parts for blasting and re-Parkerizing.

I also agree with avoiding the hydrochloric acid variants. They work, but they activate the surface so there is a tendency for surface after-rust to appear, unbidden. That activation and surface etching can be uneven. The other products above are just a better, more modern chemistry for the job. If you get after-rust from any removal compound and intend to rust blue anyway, just boil the rusted part in distilled water as soon as the rust appears to convert the red rust to black magnetite. If you are going this route (and it is a good one for home restoration where getting into molten caustic salts for hot bluing is undesirable, though pitting is tough to handle with it), be sure you've read up on rust bluing and have all the steel wool degreased or the fine brush ready that you intend to use for carding. That way accidental rust can be taken advantage of promptly.

Steel white also removes rust with less adverse impact than hydrochloric acid. It goes the other route, being mostly potassium hydroxide, IIRC. Strongly alkaline. Like lye, it is a strong degreaser as well, so you should not need a degreasing compound after using it. Just a cold water rinse that lasts long enough.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member

Last edited by Unclenick; August 17, 2009 at 07:55 PM.
Unclenick is offline  
Old August 21, 2009, 06:40 AM   #16
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,242
Damn... I figured out the problem with the action locking up...

It appears that someone decided to "adjust" the timing by thinning the hammer nose where it engages the cylinder bolt.

All their efforts did was destroy the timing. The cylinder bolt isn't being withdrawn quickly enough, so the bolt still has the cylinder locked when the hand is trying to rotate the cylinder.

Then the thin trigger nose is also release the cylinder bolt WAY early.

I think the only solution to this one is going to be a new trigger, and I really don't feel like fitting a new trigger.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old August 21, 2009, 10:03 PM   #17
BillCA
Senior Member
 
Join Date: November 28, 2004
Location: Silicon Valley, Ca
Posts: 7,087
Mike,

Unless the cylinder stop is heavily worn, my experience is that a new case-hardened trigger will need minimal fitting.

You're using the term "Hammer Nose" when I think you mean the "finger" on the front end of the trigger where it engages the cylinder stop. (S&W calls the hammer-mounted firing pin a "hammer nose").

A new trigger and new cylinder stop may need fitting to prevent premature retraction of the stop.

__________________
BillCA in CA (Unfortunately)
BillCA is offline  
Old August 22, 2009, 06:42 PM   #18
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,242
Yeah, I was talking about the wrong parts.

See what happens when you post before your first cup of coffee?
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old August 25, 2009, 06:20 AM   #19
Jdomin
Member
 
Join Date: July 29, 2005
Location: Lancaster, Pa
Posts: 93
viniger

viniger will remove bluing
Jdomin is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:46 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.10080 seconds with 7 queries