The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old July 23, 2009, 09:47 PM   #1
steven-223
Member
 
Join Date: February 13, 2009
Posts: 25
Small Ring Mauser Project

I am about to start a small ring mauser project or at least i think it is a sr mauser. I have a 1928 oviedo) does anyone know the cheapest place to ret replacement barrels. i also want to drill and tap it for a scope what is the best way to go about it? What kind of scope mount would fit & what all is involved.

Last edited by steven-223; July 23, 2009 at 09:54 PM.
steven-223 is offline  
Old July 24, 2009, 09:43 PM   #2
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,270
It is a Model 1893 Spanish Mauser, and it is small ring as they all were up to the Model 1898. Brownells has pre-threaded barrels for that action in several calibers in the same pressure range as the original 7x57, including the 7x57. I strongly suggest not trying for a higher pressure cartridge, as not only was the original design made for cartridges in the 40k-45k psi range, but Spanish-made receivers are notoriously soft.

The type of scope mount is based on what you like and can pay for, as is the scope. You will have to turn down the bolt handle or cut it off and weld a low scope type on in its place, and also fit a low-scope safety. Drilling and tapping can be done on a milling machine or with a drill press using a jig. Free-hand drilling will result in a ruined rifle. This and other work you might want to do or have done, like a new stock, rebluing, etc., will be quite costly either to have done or to buy the equipment necessary to do them yourself.

The bad part is that the rifle is one of the less desireable Mausers, so that when you are finished and have spend a fair amount of money (the barrel alone runs some $225), the rifle will bring around $150 on the used gun rack at the local sporting goods store.

If I may be honest, your questions tell me that you have not tackled anything like this before and may be getting in over your head. Might I suggest you forget the project and look around for a good used sporting rifle in the caliber you want?

Jim
__________________
Jim K
James K is offline  
Old July 25, 2009, 01:20 AM   #3
steven-223
Member
 
Join Date: February 13, 2009
Posts: 25
Thanks Jim for the information,
I had already decided away fron changing the barrel the the reason i wanted to change was because somebody attempted to sporterize it already and the person ovously didn't know what they where doing. they removed the front sight then the person drilled a hole for a new front sight (Maybee?) the hole turned out off center and ended up puting a screw in it and cutting it off. it has another hole in it that either the guy drilled or was from the original sight, all i need is a way to sight it where i can shoot it. i can post some pic where you can see what i am talking about. any sugestions
steven-223 is offline  
Old July 25, 2009, 01:21 AM   #4
steven-223
Member
 
Join Date: February 13, 2009
Posts: 25
and also the bolt handle has already been turned down that may be the only thing he done right
steven-223 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06595 seconds with 7 queries