The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old May 24, 2009, 08:31 AM   #1
velocette
Senior Member
 
Join Date: May 25, 2007
Location: South Florida
Posts: 844
Hi-Power sear spring?

I'm looking for information on how to "set" the sear spring on a MkIII BHP. I'm slowly working my way through my .40 BHP with Cylinder & Slide hammer, sear, spring kit & wide trigger. Last on the list is the sear spring. Trigger pull now is 4.75 lbs, & looking for 4#. Any suggestions?

Roger
__________________
Trigger control + Breath control + Sight alignment = Gun Control.
http://www.hrpclub.info/
NRA Smallbore Prone Master
velocette is offline  
Old May 24, 2009, 04:28 PM   #2
JMBstudent
Member
 
Join Date: November 9, 2008
Location: Rio Rancho, NM
Posts: 48
Roger,
I just finished smoothing out my HP trigger.
I noticed the C&S sear was rubbing against the frame.
I ended up reducing and polishing the sides of the sear as well as the side of the frame and ejector.
I reduced the hammer notch height to .020" and lightly polished the hamer notch sear face.
I also added a small secondary face to the sear.
Care must be taken with the hammer notch as the angle is less than 90 degrees.
The purpose of the acute angle is to trap the sear at full cock.
The geometry of the HP is not the same as a 1911.
For safety, it is important to maintain the 85/86 degree hammer notch angle. Light polishing only.
The trigger measured 3lbs 8ozs with a friends digital trigger scale.
I did not reduce the sear spring pressure.
I haven't really done any work with the sear spring or the main spring.
Maybe there is something there, I don't know.
I feel comfortable with this trigger and I would be reluctant to lighten it any further.
This from a 1911 guy with 2 1911 pistols at 2lbs 8ozs. Competition only.
I have tested my HP for hammer follow with the pistol in all positions.
It passed every test.
The trigger is clean and the break is sharp.
I'm happy, as are several people that shot the pistol.
I'm looking for a wider trigger than the stock, as that is what I prefer.
This pistol is NOT for carry. It is for target and competition work only.
I would stay closer to 5 lbs for carry.
I cannot recommend using stock parts to lighten an HP trigger as I have no experience with the stock sear and hammer.
I would suspect the hardness of stock parts.
Don't forget to double check the thumb safety after any trigger work.
Be prepared to replace the thumb safety.
__________________
JMBstudent
Learn something new each day.
JMBstudent is offline  
Old May 25, 2009, 09:00 AM   #3
velocette
Senior Member
 
Join Date: May 25, 2007
Location: South Florida
Posts: 844
JMB student;
Thanks for the information. Most of what you've suggested has been done. The sear is free of any side to side friction, I have cut a small undercut on the lower edge of the sear & deburred all corners & edges. All that is left is the sear spring that someone in the past (me) "adjusted" to cure a hammer following problem with the original hammer / sear. I just think that I went too far and I do not know where it was originally.
Incidentally, the Cylinder & Slide wide trigger is quite a bit better than the original narrow one from Browning.

Taking it out today to try to wear it out even with the 4.75# trigger pull.

Roger
__________________
Trigger control + Breath control + Sight alignment = Gun Control.
http://www.hrpclub.info/
NRA Smallbore Prone Master
velocette is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:37 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05806 seconds with 7 queries