The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old March 1, 2009, 01:36 PM   #1
gotguns?
Senior Member
 
Join Date: April 13, 2008
Location: Oakland City IN
Posts: 136
ruger blackhawk screws stuck

Im trying to dissassemble my new model blackhawk .45 colt for a complete cleaning and inspection. This is the first time ive attempted this on this gun and the screws that hold the grip frame to "main?" frame are too tight im afraid of striping them. Any tips appreciated alot.
__________________
"And what country can preserve its liberties, if its rulers are not warned from time to time, that this people preserve the spirit of resistance? Let them take arms. ... The tree of liberty must be refreshed from time to time with the blood of patriots and tyrants." -Thomas Jefferson
gotguns? is offline  
Old March 1, 2009, 02:00 PM   #2
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
Hold the gun is a steady rest, like a padded vise, rather than on a table-top or your knees - and use properly fitted, gunsmith screwdrivers that completely fill the screw slots.

Ruger uses a small dot of nylon (NyLok screws), lodged in the side of the threaded area of the screws (or used to) to keep them tight, but they might just be a little "stuck" from never being removed before.

.
PetahW is offline  
Old March 1, 2009, 02:19 PM   #3
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,247
A drop of Kroil or PB Blaster allowed to sit for a day or two will penetrate and help it break loose. I'll second the call for hollow ground gunsmith screwdrivers that fill the slot.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member
Unclenick is offline  
Old March 1, 2009, 03:06 PM   #4
dahermit
Senior Member
 
Join Date: October 28, 2006
Location: South Central Michigan...near Ohio, Indiana.
Posts: 3,505
After letting the offending screw sit with Kroil for a few days, with the gun in an appropriate vise, using the appropriate gun smith screw driver, apply the screw driver to the slot, rap on the end of the screw driver handle a couple of times smartly with a plastic/nylon hammer to loosen the screw.

If the screw does not turn with appropriate pressure, do not force it...if you snap one side of the screw head off, you are going to have to drill out the rest of the screw.

If, after the above procedures, the screw still does not want to come out, it has likely been red-loctited, and I would recommend just leaving it alone. Put the gun back together, and use it the way it is. Because, it is not broken...do not continue to try to fix it. If the day comes where you have to remove those screws, apply some heat to soften the loctite...consult with a gun smith/Ruger first.
dahermit is offline  
Old March 1, 2009, 04:38 PM   #5
jckeffer
Senior Member
 
Join Date: July 29, 2007
Posts: 182
Re: removing screws

Ditto on the above (especially PB Blaster). However I you really feel the need to remove the screw and none of the above is working you might try heating the screw with the tip of a soldering iron. It will take a while for the heat to reach the end of the screw but this will free the screw if it is held in by plastic or loctite. Depending on the type of grips you may not want to apply heat but some polymers and wood won't be hurt by the amount of heat required to loosen the loctite.
jckeffer is offline  
Old March 2, 2009, 07:44 AM   #6
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
Proper disassembly means first removing any grips - so a pin can be put through the lower end of the mainspring stud, after cocking the revolver. (and after first double-checking that's it's empty, of course)

That does two things.

Removing the grips also removes them from the work area, besides giving access to the lockwork.

Installing the pin & lowering the hammer captures the mainspring and removes pressure between the cylinder frame & the gripframe.

.
PetahW is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:00 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07430 seconds with 7 queries