The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old February 27, 2009, 01:07 PM   #1
railer12
Member
 
Join Date: December 4, 2008
Posts: 41
fixed sight adjustment on S&W

I recently purchased a S&W model 547, 3 in. barrel. Love this little 9mm revolver, but it shoots about 2-3 in. left at 25 yds. Is there anyway to adjust the front sight? (this gun has fixed sights). Sight needs to go left just a bit, but don't want to take a chance on breaking it.
railer12 is offline  
Old February 27, 2009, 01:31 PM   #2
James K
Staff
 
Join Date: March 17, 1999
Posts: 18,647
Not a lot you can really do except to hold off. There will likely be a lot of ideas about bending, welding, filing, etc., but those things are easier to say than to do without wrecking the gun. 2-3 inches is not much at that distance from what is basically a short range revolver. I would rule out my shooting (let another good shooter try it from a rest) and then if it is confirmed, just live with it.

Jim
__________________
Jim K
James K is offline  
Old February 27, 2009, 01:32 PM   #3
hunter11
Member
 
Join Date: January 31, 2009
Location: Florida
Posts: 66
Sight adj.

Put a small dab of fingernail polish on the side of front sight. Dan
hunter11 is offline  
Old February 27, 2009, 02:21 PM   #4
railer12
Member
 
Join Date: December 4, 2008
Posts: 41
Thanks Jim, I think your right.

I don't get the fingenail polish on the sight theory, could you explain hunter11.
railer12 is offline  
Old February 27, 2009, 02:25 PM   #5
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,340
Something else you might want to try is firing several types or makes of ammo to see if there is a POI shift right or left. You may find a load that shoots right on.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old February 27, 2009, 02:33 PM   #6
railer12
Member
 
Join Date: December 4, 2008
Posts: 41
Good point scorch. My sig sp2340 is exactly like that. I've only shot Remington 115 gr.FMJ in this.
railer12 is offline  
Old February 27, 2009, 02:42 PM   #7
madmo44mag
Senior Member
 
Join Date: December 29, 2008
Location: Ft.Worth, Texas
Posts: 879
If you have trouble getting it sighted in and just cant live with it, you can give it to me - lol!
Sight off the left side of the front blade and line it right behind the right rear side site
I have a Rossi 44Spl snubbi that way and it has adjustable sites.
Work for me.
__________________
Texas - Not just a state but an attitude!
For monthly shooting events in DFW visit http://www.meetup.com/TexasGunOwner-DFW
madmo44mag is offline  
Old February 27, 2009, 02:53 PM   #8
railer12
Member
 
Join Date: December 4, 2008
Posts: 41
LOL... thanks Madmo, but I think Jims post is the best I've heard so far.
railer12 is offline  
Old February 27, 2009, 04:18 PM   #9
Japle
Senior Member
 
Join Date: October 12, 2004
Location: Viera, Florida
Posts: 1,168
That's within factory specs for a fixed sight revolver.
You can open up the right side of the rear sight notch if you can live with a wider notch. You can also have the barrel cranked a bit to the left and the cylinder gap adjusted. Don't try this at home!!

Seriously, there's not much you can do except experiment with loads and see if you can find something that shoots closer to your POA.
Japle is offline  
Old March 2, 2009, 09:07 PM   #10
HiBC
Senior Member
 
Join Date: November 13, 2006
Posts: 3,403
When I bought a Uberti .45 LC single action a cowboy shooter friend advised I experiment with loads.It worked,and not only on elevation.
Another possibility would be to try different grips,like Hogues or Pachmayers.

Just for info sake,if you convert ther sight radius and the range to the same unit of measure
say 0.5 ft and divide it into the range (75 ft) you would know the multiplier of a sight change,in my hypothetical case 150.So,with a 6 in sight radius,moving the centerline of the blade or notch .020 would move POI 3 in at 25 yds.Someting to remember is the effect is split in half if you cut one side of the blade or notch,as you still center the sight picture,so I would have to take .040 off one side to move the center line .020.

.040 is a lot! It would look like something was wrong.

I am telling you this to re-enforce getting the dremel out ( :-) isn't the best plan here.

Last edited by HiBC; March 2, 2009 at 09:19 PM.
HiBC is offline  
Old March 2, 2009, 11:53 PM   #11
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 9,211
I know this is gonna sound stupid, but it works sometimes. Change ammo. differant ammo affects differant guns in differant ways. Change bulles, change powder charge, change brass, change primers. You'd be supprised.

I had a 547 that was off, (forgot, which way, but is was one side or the other). I kept playing with it until I found a charge of powder bullet combo that worked. I was by using the lyman 356402 146 grn bullet. I forgot the powder charge, it was a while back and I got rid of my notes when I sold the gun (which was a stupid move on my part). I loved that little gun.
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School Oct '78
Distinguished Rifle Badge 1071
kraigwy is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:09 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08667 seconds with 7 queries