The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old February 7, 2009, 08:04 PM   #1
aardvarkrh
Junior Member
 
Join Date: May 19, 2008
Location: Between Bay Area & the Goldcountry
Posts: 8
1858 Pietta Conv cyl ???

Just got a conv. cyl. from Midway. Bought sum Winchester "cowboy ammo" & tried to load. Wouldn't seat and rims interfered. Wrong cyl...? or am I f'd up.

Midway was great..., as usual, and said they'd "check it out". Shipped back, and am waiting. Am I doing sumthin wrong?

Much thanks from a relative newcomer.

ARD
aardvarkrh is offline  
Old February 7, 2009, 09:19 PM   #2
grymster2007
Senior Member
 
Join Date: May 22, 2007
Location: In the oak studded hills near Napa
Posts: 2,203
My R&D conversion cylinder required reaming the pin bore before I could install it on my 1858. I didn't know whether to blame R&D or Pietta, but the fix was pretty easy. Your problem sounds like it might be an R&D issue and a bit more difficult to solve.
__________________
grym
grymster2007 is offline  
Old February 8, 2009, 02:10 AM   #3
Smokin_Gun
Senior Member
 
Join Date: December 4, 2005
Location: Mojave Desert, CA
Posts: 1,195
aardvarkrh,
What caliber 1858 Remington R&D Conversion is it? .45 Colt or 38 Colt?
Did you happen to buy Schofield .45's? Some cyl. will take the .45 Colt and not the .45 Schofield(shorter ones) for the way the cut for the rim in the cylinder is.
Now if it's say a .38 Colt you ordered and they sent a .38SPL cyl. then the .38 Colt Cowboy ammo would like as not fit right in the cylinder of a .38SPL as the .38 Colt bullets are heeled to fit the barrel.
Somethin' like that could a happened. Real good question though and topic...

SG
__________________
"I Smoke Black Powder" "Favor an 1858 Remington"
SGT. Smokin' Gun, Mosby's Rangers 43rd Virginia Cavalry C.S.A.
SASS# 19634, ...
Admin:http://blackpowdersmoke.com/oldcoots/index.php
Smokin_Gun is offline  
Old February 8, 2009, 05:15 AM   #4
darkgael
Senior Member
 
Join Date: February 9, 2006
Location: Homes in Brooklyn, NY and in Pennsylvania.
Posts: 4,330
1858

+1 on that caliber check. I have an R&D .38 Special cylinder for the Pietta New Army Police .36. It dropped in and works perfectly.
As noted, could be you were sent the wrong one for your gun.
Pete
__________________
"Only hunting and mountain climbing are sports. The rest are just games." - R.Ruark
NRA Life Member
darkgael is offline  
Old February 8, 2009, 10:41 AM   #5
tatso7
Senior Member
 
Join Date: March 22, 2006
Location: southwest
Posts: 107
Check if you have the right cylinder. Take note that R and D makes 1858 conversion cylinder for 45 LC and for .44 Colt cartridge . The 45 LC cartridge will not fit in a 44 colt cylinder.

Last edited by tatso7; February 8, 2009 at 10:47 AM.
tatso7 is offline  
Old February 8, 2009, 11:54 AM   #6
aardvarkrh
Junior Member
 
Join Date: May 19, 2008
Location: Between Bay Area & the Goldcountry
Posts: 8
1858 Pietta conv cyl ????

Thanks for all the response. After speaking with Midway, They believe that it's probably just the wrong cylinder. Everyone else I spoke with at the range has had little if no problem, with the correct cylinder. Fingers crossed.

Thanks to all who resonded, again!

ARD
aardvarkrh is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:01 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08038 seconds with 7 queries