The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old January 30, 2009, 10:09 AM   #1
DadsMod12
Junior Member
 
Join Date: January 7, 2009
Location: West Central Ohio
Posts: 10
Finish on inside of wood grip

I was looking at the walnut grips on my Beretta 92FS and noticed that the insides were unfinished. Should I put a couple of coats of poly on the back side to protect it from any clp or oil that might get on the grips. Thanks in advance for your help.
DadsMod12 is online now  
Old January 30, 2009, 04:35 PM   #2
sadsack
Senior Member
 
Join Date: February 4, 2006
Posts: 206
M-12: It would be a good idea to finish the inside for the reasons you mentioned and more.
sadsack is offline  
Old January 31, 2009, 07:22 PM   #3
Derekadavis
Senior Member
 
Join Date: December 27, 2008
Location: Dallas,Tx
Posts: 102
i was wondering did the wood grips make the grip any wider i want some on my taurus pt917 but i was worried about it making it to wide..
__________________
USCCA & NRA Member
Derekadavis is offline  
Old February 1, 2009, 04:19 PM   #4
KEN K
Senior Member
 
Join Date: October 7, 2006
Location: mid west Georgia
Posts: 102
What Sadsack said.
KEN K is offline  
Old February 1, 2009, 08:13 PM   #5
DadsMod12
Junior Member
 
Join Date: January 7, 2009
Location: West Central Ohio
Posts: 10
Thanks Sadsack & Ken. FYI the grips are custom grips and are 3/16" thick.
DadsMod12 is online now  
Old February 1, 2009, 10:42 PM   #6
Tom2
Senior Member
 
Join Date: June 23, 2004
Location: Ohio
Posts: 5,648
Most wood grips are not finished on the insides. That probably allows some moisture to absorb from the palms of your hands. That may be why old guns have pitting all around the edges of the grips on the frame, underneath them. So I can't imagine a coating of something to seal the wood would hurt a thing. Then again there may have been a rationale for not doing it in the past, besides being cheapo on the varnish.
__________________
Your gun is like your nose, it is just wrong for someone else to pick it for you!
Tom2 is offline  
Old February 4, 2009, 02:54 AM   #7
roklok
Senior Member
 
Join Date: October 20, 2008
Location: Fort Yukon, Alaska
Posts: 692
The first thing I do when I buy a new firearm with a wood stock or grips is to do my best to seal all exposed wood. I pull buttplates, grip caps off of long gun stocks and varnish under them, as well as handgun grip panels. I use Thompsons water seal in cut checkering, this keeps water from soaking into exposed raw wood in checkering pattern. If you carry a gun in the rain without weatherproofing the unfinished wood, the moisture will soak under the finish, causing it to flake off.
roklok is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:53 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07366 seconds with 7 queries