The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Curios and Relics

View Poll Results: Should I drill & tap an M96 for a scope mount?
Yes 6 50.00%
No 6 50.00%
Voters: 12. You may not vote on this poll

Reply
 
Thread Tools
Old January 12, 2009, 11:54 AM   #1
The Lovemaster
Senior Member
 
Join Date: December 29, 2007
Location: Arizona
Posts: 416
Should I Scope an M96?

So I have this sweet M96, but the guy I bought it from refinished the stock. The gun is beautiful, but the collector value is shot due to the stock.

Should I have the receiver drilled and tapped for scope mounts? I'm a scope guy, and this gun would be sweet out to 1000 yards.
The Lovemaster is offline  
Old January 12, 2009, 12:03 PM   #2
jsmaye
Senior Member
 
Join Date: July 18, 2008
Location: Amarillo, Tx
Posts: 616
My opinion is that it's your rifle, do as you please. The fact that the rifle has been altered just eases the conscience a bit.
jsmaye is offline  
Old January 14, 2009, 01:33 AM   #3
sliverflinger
Member
 
Join Date: January 20, 2008
Posts: 18
should I scope my 96

It is your rifle, but d&t ing it will decrease the value. This just my two cents worth, but I'd look for one that has already been done. They are generally cheaper.Then you'll have one that goes up in value, and one to play with.I hunted for months to find one that had been "sporterized" (bubba took a saw to the stock and barrel both). Got it for about half what a stock rifle would cost .A stock swede is great to shoot, but if you want a scope thats the way I'd go. Just my opinion.
sliverflinger is offline  
Old January 14, 2009, 11:35 AM   #4
The Lovemaster
Senior Member
 
Join Date: December 29, 2007
Location: Arizona
Posts: 416
That's a good suggestion, thanks dude.
The Lovemaster is offline  
Old January 14, 2009, 12:15 PM   #5
aerod1
Senior Member
 
Join Date: April 12, 2000
Location: Garland Texas U.S.A.
Posts: 730
I agree with sliverflinger. If it were mine, I would not drill and tap it.
I bought a m94 that had already been bubbaized with the drill and tap job. It came with the rings already mounted. I gave $125.00 for it and then put a Tasco 3x9x40 scope on it. It is one of my favorite rifles and it always holds POA even after bouncing around in the rack of my ATV. I have taken the last 4 deer with this gun while my Winchester model 70's and Remington 700's sit in the safe.
In my opinion the 6.5x55 Swede cartridge is the finest deer cartridge there is.
The m94 is short and easy to handle while hunting.
__________________
NRA Life Member, TSRA Life Member,
C&R 03 FFL, Texas CHL
Recreational Reloader
U.S. Navy Veteran (USS Midway V-1 Division)
aerod1 is offline  
Old January 14, 2009, 12:26 PM   #6
DoctorXring
Senior Member
 
Join Date: April 30, 2002
Location: The Republic of Texas
Posts: 389
.

If it's a gun you plan on keeping and it will increase
it's value to YOU, go ahead and scope it.

I have an RC K98 that I tapped and scoped. I put an
older Weaver scope on it and it still retains a period
look to it. I love shooting it and don't plan on ever
selling it. I also put a Boyd trigger in it. Pillar bedded
and floated barrel. BTW, I've been offered a large
packet of folding money twice for this rifle at the range.
So I can't totally buy off on that always decreasing
the value. It just depends. Each rifle is an individual.

I agree however, that doing such behaviors toward a
truly collectible rifle is foolish.

best, dxr



DoctorXring is offline  
Old January 16, 2009, 06:27 PM   #7
10 Spot Terminator
Senior Member
 
Join Date: January 3, 2008
Location: Central Oregon
Posts: 346
I have one currently under construction and cant wait to have it completed. I have the bolt out having the handle turned down ( not bent ) so as to make it look as if it were from a later model 42B . By doing this I can stay with the lower scope mounts and actually be able to address the scope with my cheek planted firmly on the stock. I have an early Weaver scope that will look right at home on the 96 and allow me to actually see what I am shooting at . I can print 1 1/4 inch groups as it is having to shoot at big 6 inch target dots with iron sights and hope to cut that in half or better with a scope .
10 Spot Terminator is offline  
Old January 24, 2009, 11:29 AM   #8
Tadpole Starr
Member
 
Join Date: February 28, 2007
Posts: 52
I have one with matching S/N scoped

It is a real shooter, but I am sorry that I had it altered. It even has the proper bayonett. I would not ruin the value of it as a shooter, unless one cannot be found. It is not one to use in the woods, due to the length, so it must be used on the range. Just a thought. Tad
Tadpole Starr is offline  
Old January 24, 2009, 12:06 PM   #9
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 11,694
It's not just a matter of drilling and tapping. You're going to have to have work done on the bolt handle or replace it. Replacing looks a lot better and you're going to have to change out the safety too.
Hawg is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:26 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08483 seconds with 10 queries