The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 3, 2008, 01:01 PM   #1
blu97
Member
 
Join Date: June 12, 2008
Location: California
Posts: 81
Enfield barrel question

I have a very nice enfield no 4 barrel i would like to know the twist rate of.

The barrel is 25.5 inches long and with a cleaning rod I got 2.25 turns.

I'm not sure how to figure the rate.
blu97 is offline  
Old November 3, 2008, 01:07 PM   #2
4thPointofContact
Junior member
 
Join Date: September 22, 2007
Posts: 197
25.5 divided by 2.25 = 1 turn every 11.355 inches.
I found this info online for the No.1 Mk III, I shouldn't imagine they changed the rifling just to go to the No.4


S.M.L.E BRITISH
NO.1 Mark III Short Lee Enfield.
Adopted: 1907
Cal: .303
Length: 44.5"
Wt: 8.6lb
Action: Turnbolt
Bolt: 2 Piece non rotating head
Mag: Detach Bx. Stagg. Column
Capacity: 10 rnds
Bbl length: 25.2"
Bore Dia: 303"
Twist: Left
Rate: 1 in 10 inches


EDIT: Link to Lee Enfield No.4

Last edited by 4thPointofContact; November 3, 2008 at 01:17 PM. Reason: Found link to No.4
4thPointofContact is offline  
Old November 3, 2008, 01:12 PM   #3
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 9,553
I'm assuming you are talking the Model 1917 Enfield in Cal 30 (30-06)

The normal barrel was 26 inches, five grove, left hand 1 in 10.

Some of the 1917s were rebarreled in WWII with two grove right hand twist the same as the M1903 A3.

Hope this helps,
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School Oct '78
Distinguished Rifle Badge 1071
kraigwy is offline  
Old November 3, 2008, 02:57 PM   #4
James K
Staff
 
Join Date: March 17, 1999
Posts: 20,001
Blu97 said it was a No. 4 barrel, not a M1917 barrel. Anyway the No. 4 twist rate is normally 1 turn in 10 inches (1:10), left hand. Some Savage barrels are 1:10.5 and some Long Branch barrels are right hand twist, but neither matters for practical purposes.

The usual way of measuring twist is to take a cleaning rod and use a patch tight enough to be sure the rod turns with the rifling. Then insert the rod into the barrel, and mark one side of the rod at the muzzle. Pull the rod out, letting it turn with the rifling. When the mark is once again on the same side, measure the difference between it and the muzzle. That is the rifling twist. For rifles of .30 or .303, it is usually 1 turn in 10 inches, so the distance measured should be 10".

Jim
__________________
Jim K
James K is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:54 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06176 seconds with 9 queries