The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools
Old November 2, 2008, 10:27 AM   #1
rogertc1
Junior member
 
Join Date: December 17, 2004
Location: Maquoketa
Posts: 1,335
Just bought a Astra M900 Broomhandle

Better shape than I expected for a inexpensive Broom Handle type pistol. I have searched but can't find a site with when it was made. Anyone know?
Also how to dissasemble.

SR # 24122X

Link of where I bought it...(Hyatt are really great to buy from.)
http://www.gunbroker.com/Auction/Vie...Item=113286533


Thanks
Roger
rogertc1 is offline  
Old November 2, 2008, 11:13 AM   #2
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 10,904
Although patented in 1928, one source says they were in production by 1927
http://www.gunsworld.com/spain/astra900_us.html
They were still cataloged in 1938 but did not likely survive the war.
If I can find my article on Spanish proof marks, I will try to tie it down closer.

From an article by Larry Sterett in an old Gun Digest. (I don't know how old, I read and reread it as a kid and it is eroded several pages from each end, including cover and spine. Maybe 1959 or 1960, based on new gun introductions.)

"The disassembly of the Astra models differs radically from that of the Mauser. The following procedure should be used:

1. Cock the hammer and place the lower edge of the safety lever in line with the groove on the sliding cover. Placing the barrel against something solid, push it backwards, or grip the barrel in the left hand and push it rearward. Uding the right forefinger, push the rear bolt, located above the caliber mark, through from the right side.

2. The cover may now be slid backward with a slight pressure of the left thumb, exposing the interior mechanism for inspection.

3. Place the safety lever in firing position, push the barrel backwards, and purh out the round headed bolt in the center of the frame, from right to left. Be careful when removing this bolt as the pressure of the stop spring will now cause the frame and barrel to separate. Remove the safety lever.

To assemble, reverse the above operations."


They always say that, don't they?


Found my book. One of the proof marks, the knight's helmet over a shield with crossed muskets, came into use in 1931, so the gun was made not earlier than that. Spain had not changed proof marks in the next 40 years so I cannot fix it any closer than 1931 til the end of production. Which one source says was 1933 and another 1941. A third says... well read it at
http://www.1896mauser.com/spanish.htm

Last edited by Jim Watson; November 2, 2008 at 09:19 PM.
Jim Watson is offline  
Old November 2, 2008, 03:53 PM   #3
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 16,595
Astra and Star both capitalized on the Mauser's popularity in the Asian market. One major derivation from the Mauser design was the abandonment of the interlocking feature of the Mauser. Mauser had only one screw (grip) and one pin (sight for adjustable sights) in its construction. Everything else snapped together like a lego brick. Astra relied on more convention manufacturing techniques (cheaper to machine) to make their copy of the Broomhandle.

Congratulations on your acquisition.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:01 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06151 seconds with 7 queries