The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old November 1, 2008, 06:03 PM   #1
polkey
Junior Member
 
Join Date: October 25, 2008
Posts: 5
Rust removal

Got a new S&W DA .38 revolver, only problem is it's got a bit of rust, if anybody knows how i can get it off without ruining the rest of the finish, tips would be appreciated
Attached Images
File Type: jpg 4 sw rev 110.jpg_thumbnail1.jpg (99.9 KB, 99 views)
File Type: jpg acfe871.jpg (81.5 KB, 86 views)
polkey is offline  
Old November 1, 2008, 07:16 PM   #2
fastforty
Senior Member
 
Join Date: December 28, 1999
Location: In a kornfield in kalifornia
Posts: 1,161
Before I looked at the pics, I was going to tell you to get an old real-copper penny & use it to rub the high spots off (won't damage existing bluing). Then I looked at the pics. It looks like it's been shot with corrosive powder & not cleaned properly (edit: Ok, now I remember, I'm in the BP forum, LOL). It looks bad enough to go after it with a soft metal wire wheel on a bench grinder (not sure if it really is as extensive as it looks). That much rust has surely gotten under & lifted some of the plating off.

Rather then looks, I'd be more concerned about the condition of screws, pins, and the inside of the cylinder & bore. You may have what will be a good shooter for a long time, if it passes mechanical inspection. I'd say that a complete teardown is in order, for cleaning & inspection.
__________________
When Banjos are outlawed, only Outlaws will have Banjos
The Bible is my lawbook. I turn the other cheek when applicable, and spend the rest of my days resisting evil at every front, until I have breathed my last breath.

Last edited by fastforty; November 1, 2008 at 07:19 PM. Reason: Duh
fastforty is offline  
Old November 1, 2008, 07:36 PM   #3
polkey
Junior Member
 
Join Date: October 25, 2008
Posts: 5
person i bought it from had it inspected before i bought it and it's safe and locks up fine. haven't actually fired it yet wanted to clean it it up a bit first.
i was looking for more of some kind of solvent or something like that and just soak it for a while, want to keep it as original as possible. nothing to evasive.
polkey is offline  
Old November 1, 2008, 07:45 PM   #4
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 11,753
You're going to lose a lot of plating no matter what you do. Going to be some pitting too. Under the rib is probably going to be the worst from the look of the pics. Maybe some Kroil and 0000 steel wool
Hawg is offline  
Old November 1, 2008, 09:53 PM   #5
mykeal
Senior Member
 
Join Date: October 8, 2006
Location: Northern Michigan
Posts: 2,760
Nevr-Dull, plus some 0000 brass wool. Will remove rust and reveal pitting if any, will not fix pitting.
mykeal is offline  
Old November 1, 2008, 10:07 PM   #6
ZeSpectre
Senior Member
 
Join Date: June 4, 2007
Location: Shenandoah Valley
Posts: 3,276
Makes me sad.
Really I'd say take it to a professional and have it done up right.
ZeSpectre is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:58 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07288 seconds with 8 queries