The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools
Old April 19, 1999, 01:42 AM   #1
jose
Junior Member
 
Join Date: April 18, 1999
Posts: 1
H&R 922

The H&R 922 is a 9 shot .22 revolver.
I was wondering if anyone knows any history of this firearm, as to how old it may be or even what one may be worth in decent condition. Any feedback would be appreciated.
jose is offline  
Old April 19, 1999, 03:33 AM   #2
Gunslinger
Junior member
 
Join Date: January 5, 1999
Location: Springfield, Missouri
Posts: 2,105
The 922 was produced from 1950 until 1982. Value is from $85 to $25 from 100% to 60% respectively.
Just my opininion but they are a good, solid and inexpensive fun gun. Not really worth much in $$$ but none the less very enjoyable to own.
Gunslinger is offline  
Old April 19, 1999, 09:52 AM   #3
JBP
Senior Member
 
Join Date: October 13, 1998
Location: Maryland
Posts: 471
I've had mine for about 20 years. Still take it out to the range a couple of times a year and it keeps on firing. Just sorry I did not get the .22 Magnum H&R at the same time.
JBP is offline  
Old April 19, 1999, 02:25 PM   #4
John/az2
Senior Member
 
Join Date: February 18, 1999
Location: Arizona
Posts: 2,729
You may want to take this question to "Harley Noldan's Institute for Firearms Research." It's right under "Legal and Political" on the main screen of this site.

------------------
John/az

"Just because something is popular, does not make it right."

John/az2 is offline  
Old April 19, 1999, 03:19 PM   #5
Harley Nolden
Staff In Memoriam
 
Join Date: January 8, 1999
Location: Brunswick,GA USA
Posts: 1,884
Jose:
The H&R 922 came in two issues.
1st Issue: Was a solid frame .22 cal Long Rifle Ctg. 9 shot. The barrel came in 6" on later productions, early model 10-" barrel. Wetigh with 6" bbl=26oz. Fixed sight Blued finish. Checkered walnut stocks. Safey cylinder and round barrel on later models, earlier production had octogon barrel..Discontinued in 1942.

2nd Issue: Basically the same as the 1st issue in caliber with 9 shot capability. Barrel lengths 2 1/2", 4",and 6". Weight 4" bbl 24oz. Fixe sights. blued finish, plastic stocks. Made from 1950 to 1986.

NOTE: Current Model 922 has a differeent frame from that of the First Issue. Model 923 is the same as MOdel 922 2nd issue except for Nickle finish
I have the disassem/assem instructions if you want them. If so kindly refer to Library volume #4 upon your request.
HJN
Harley Nolden is offline  
Old April 20, 1999, 12:35 AM   #6
Ed
Member
 
Join Date: November 13, 1998
Location: Geogia, USA
Posts: 85
I know they sold for $32.50 when I bought one in 1955. I remember because it was my first handgun and I had to save out of my $40 a week job to buy it. I could have gotten an Iver Johnson 8 shot .22 for about $26 but it had a pull-pin cylinder, and the H&R had a swing-out 9 shot cylinder, so I just saved another few weeks for the H&R.
Ed is offline  
Old January 28, 2009, 11:21 AM   #7
warnpeace
Junior Member
 
Join Date: January 28, 2009
Posts: 1
hey guys, I did a search and this thread came up. I hope its not too old. I am looking for a cylinder pin for a H&R 922 like the one's you are discussing. it is one of the earlier models without the round barrel, sort of an octagon shape. I would appreciate any advice or direction from you. thanks for your time. peace..........or war, whatever.
warnpeace is offline  
Old January 29, 2009, 07:10 PM   #8
32 Magnum
Member In Memoriam
 
Join Date: January 17, 2009
Location: Eastern PA
Posts: 364
Check out: auctionarms.com and/or gunbroker.com for parts for the H&R revolvers (search both 'H&R' and 'Harrington & Richardson'). Warnpeace You have a first model - made before 1952. If you provide the serial number, I can tell you the variation and era of manufacture. The 922 was in continuous production from around 1926 -27 up to around 1970 in two model runs. It was resurrected in the mid 1970s and then ran up until H&R folded in Early 1986. I have examples of all 7 of the first model variations as well as of the 5 2nd model variants. Cylinder pins varied considerably from variation to variation and within the models. With serial number I can tell you what cylinder pin you need.
Jim Hauff, H&R Collector

Last edited by 32 Magnum; January 31, 2009 at 09:42 PM. Reason: added information
32 Magnum is offline  
Old January 29, 2009, 08:35 PM   #9
Tom2
Senior Member
 
Join Date: June 23, 2004
Location: Ohio
Posts: 5,647
What about Numrich? Or I suppose that if someone would make an accurate drawing of theirs with measurements, a machinist could turn you one out on the lathe? Not like it has to be special or a certain steel like a barrel or cylinder. Or being on a rimfire, not a high stress part. One thing that bothers me is I have one of those topbreak prewar H&R .22 Specials that needs work. Blueing excellent, bore mint. Perfect Roper grips. but some chump went to work on it, filed on the rear sight and hammer, and butchered up the extractor star so the ratchets look like a mess. Saw another with the good parts but a bulged barrel, and the bozo would not go less than 160 for it, he claimed the obviously bulged barrel was just fine...So mine is collecting dust.
__________________
Your gun is like your nose, it is just wrong for someone else to pick it for you!
Tom2 is offline  
Old March 30, 2009, 10:20 AM   #10
22revolver
Junior Member
 
Join Date: March 30, 2009
Posts: 1
hey i have a H&R 922 with serial number J35359. can anyone help me find out where i can get a cylinder pin for it?
22revolver is offline  
Old March 31, 2009, 02:24 PM   #11
jamesjo
Senior Member
 
Join Date: August 23, 2007
Location: Nebraska
Posts: 195
Try Numrich gun parts
jamesjo is offline  
Old March 31, 2009, 08:13 PM   #12
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,682
Numrich is www.gunpartscorp.com. They list center pins for H&R revolvers at around $7. Follow their directions as to which one you need. Yes, one can be made, but no one is going to do it for under $10.

Like other such parts, they can be made by a gunsmith, but not many people are willing to spend $50 or so for a simple part that can be bought, especially when the gun is not worth the cost of the part.

Now when you desperately need a part for an old Colt, say, that is worth $3000 in working condition and $1000 with a broken part, making the part is well worth it. With a gun that is worth under $100, the cost of having a part made is questionable.

Jim
__________________
Jim K
James K is offline  
Old December 4, 2009, 09:49 PM   #13
ganderite
Junior Member
 
Join Date: December 4, 2009
Location: Canada
Posts: 1
H&R 922 woes

A friend of mine has a 922 that he has owned since new. It has a 4" barrel.

In Canada, this length of barrel is considered "Prohibited" (don't get me started...). he would have been allowed to keep it, if he had remembered to re-register it - but he did not.

Now he has to turn it in unless it gets re-barreled to 4 1/4" or longer. I looked on the Nurmich pages, and they show lots of longer barrels, but not for a 922.

I could buy a 6" for any model and just cut new threds and a forcing cone, but that is a lot of work on a $100 gun.

I am hoping that one of you will know of a different model that uses the same thread diameter and shank length.

Or maybe one of you has a 6" 922 and wants to trade the barrel for a 4" ????
ganderite is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:04 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09050 seconds with 7 queries