The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old October 4, 2008, 11:03 PM   #1
cchardwick
Senior Member
 
Join Date: September 26, 2008
Location: Colorado
Posts: 574
Extended magazine tube for a Marlin 1895?

I have a Marlin 1895 lever action, 45-70 caliber and the magazine only holds four rounds (4+1). But I've seen 'custom' 1895s that have an extended magazine tube that actually holds 6 rounds (6+1). Anyone know where I can get an extended tube? Anyone know if I can install this myself or if this is a gunsmith installed item?

cchardwick is offline  
Old October 5, 2008, 12:13 AM   #2
Big Caliber
Senior Member
 
Join Date: October 10, 2006
Location: S. CA
Posts: 396
If ya find out, please let me know.
Big Caliber is offline  
Old October 5, 2008, 11:33 AM   #3
ocharry
Senior Member
 
Join Date: October 20, 2006
Posts: 221
you can make your mag tube longer,,i did this to a 38-55 that i had

you need a mag tube from numric gun parts or some one else,,, or buy two and save your original,,,,you will probably only use 6-8" of one of them to get the length you need

measure to see how much you need to add,,,on mine i turned the end of one and bored the end of the other for a nice press fit,,,heat up the bored end and slip the two together ,,, once they were together and straight i silver soldered them so they wouldn't come apart,,,,the forearm covered the joint

the problem you will run into will be the barrel hanger,,,on the full magazine guns,,,some have a dovetail in the end of the barrel and some use a band

if you have a dove tail now you will need to cut a dove tail in the end of your barrel to support the mag tube

if you have a band now and you move it out the the end of the barrel you may need to cut a notch in the bottom of the barrel to clear the screw that goes through the band for mag support

IIRC the end of the mag tube that goes into the receiver is turned to fit,,,and should pull out

you may contact marlin and buy a one piece tube and spring,,,,, but depending on how long your barrel is you may need to cut it to the proper length

my .02 YMMV

ocharry
__________________
YHS
ocharry
ocharry is offline  
Old November 24, 2008, 06:58 PM   #4
zoomie
Senior Member
 
Join Date: January 23, 2006
Location: WY
Posts: 1,752
Thread revival:

If you're like me - I wouldn't attempt it myself. Wild West Guns and Brockman's offer the service, usually in conjunction with a cut and crown, or

http://www.brockmansrifles.com/lever_cust.asp
http://www.wildwestguns.com/
zoomie is offline  
Old November 25, 2008, 05:16 PM   #5
Cowart
Senior Member
 
Join Date: March 15, 2007
Posts: 247
Instead of lengthening a short tube, it would be better to purchase a 26" long 9 shot tube intended for the 1895 "Cowboy" model, and shorten it. It's Marlin part # 101125
Cowart is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:40 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06615 seconds with 7 queries