The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old September 28, 2008, 03:01 PM   #1
mikenbarb
Senior Member
 
Join Date: October 10, 2007
Location: N.J.
Posts: 1,111
How good are barrel liners for a rimfire?

I got a shot out .22 rimfire and wondering if its worth the money to have a liner installed vs another barrel. Its for an old Savage single shot bolt action. And where is a good place to buy one except Midway? Thanks.
__________________
Mike B.
Gun control= Being able to hit your target.
http://groups.yahoo.com/group/pifinnercircle
mikenbarb is offline  
Old September 28, 2008, 04:47 PM   #2
Tom2
Senior Member
 
Join Date: June 23, 2004
Location: Ohio
Posts: 5,647
I have had guns relined and it works OK as long as the smith does a good job of it. First the gun must be worth the trouble or something that is an heirloom or just that you want to shoot, as with alot of cheap rimfire rifles, the cost of relining it correctly may not be economical. A good smith can make the seam at the muzzle practically invisible. Then they have to chamber the liner correctly at the other end of the barrel. But once it is done, it can make a shooter out of a dud. It is not something I would try to do myself without being a machinist or having smith experience. But I think a rimfire job would be cheaper than the centerfires I had done. As for a new barrel, where do you expect to find a good barrel for an old rifle like that? Probably any pulled barrels that might match the gun will be not alot better. If you really think the gun is a keeper or will get alot of use out of it, then the cost may be immaterial as you are looking at using, not turning around for a profit, which will be nil. Talk to the smith who will be doing the work, versus trying to buy it and then have them install it. There are some listed in places like Shotgun News gunsmith section.
__________________
Your gun is like your nose, it is just wrong for someone else to pick it for you!
Tom2 is offline  
Old September 28, 2008, 05:47 PM   #3
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,507
I would recommend a new barrel if feasible. Relining a barrel works fine, but the machine time required and the labor required may cost as much as a new barrel.
You can buy barrel liners from Brownells or Midway.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old September 29, 2008, 09:42 PM   #4
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 9,515
I've relined several 22 barrels. I think that would be a cheaper route. Brownells instructions say you can do it with a slow turning power drill but I do it on a lathe. Its really simple, get the drill bit from brownells when you get the liner. Drill out the barrel from the breach in. Take some ruff sand paper and bullf up the out side of the liner. Clean the cutting fluid out of the barrel. You can either silver soder the liner in or like I do, use Brownells accra jel (thats why you ruffed up the liner). Slide the barrel in. Chamber and head space it then cut the crown. I'll rebarrel or instal the liners, I'd charge more for the re-barreling. There is more work to re-barreling.
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School Oct '78
Distinguished Rifle Badge 1071
kraigwy is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:44 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07694 seconds with 9 queries