The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old August 27, 2008, 09:12 PM   #1
TheShootist1894
Senior Member
 
Join Date: May 24, 2007
Location: Putnam County Ohio
Posts: 324
Loading Wadcutters in 357 Mag, HeLP

What do I need short of the regualar dies I have for 357, have been shooting wadcutters for some time, and reloading other 38/357's but would like to be able to 'roll my own' wadcutters

Thanks
Karl
__________________
_____________________________________________________________________
Sturm Ruger-Bolt & High End Single Shot Rifles: Remington-Shotguns: Smith & Wesson-DA Revolvers: Sturm Ruger-SA Revolvers: Marlin/NEF/H&R-Best BANG for your Buck!!
Quality + Accuracy + Value =
TheShootist1894 is offline  
Old August 27, 2008, 09:21 PM   #2
shepherddogs
Senior Member
 
Join Date: January 9, 2007
Posts: 1,007
I think you can melt candle wax into the hollow part of the bullet seater. This makes it reasonably flat for seating and doesn't permanently damage the seater. Just heat it up and the wax melts out.
shepherddogs is offline  
Old August 27, 2008, 10:33 PM   #3
zxcvbob
Senior Member
 
Join Date: December 20, 2007
Location: S.E. Minnesota
Posts: 4,155
You don't have to do anything different. The regular dies and seating plug will work just fine. Are you talking about loading light target loads, or .357 Magnum DEWC sledgehammers?
__________________
"The only way to stop a bad guy with a gun is with a good guy with a gun"
zxcvbob is offline  
Old August 28, 2008, 12:07 AM   #4
Wuchak
Senior Member
 
Join Date: June 1, 2007
Location: Shawnee, KS
Posts: 1,093
There is nothing different about loading wad cutters vs another shaped bullet.
Wuchak is offline  
Old August 28, 2008, 12:34 AM   #5
joneb
Senior Member
 
Join Date: December 10, 2005
Location: Central , OR
Posts: 1,731
I was getting leading with Magnus 148gr swaged HBWC in both .38spl and .357 mag. the problem was the swc seater plug in my RCBS dies was not compatable with this bullet. My solution was to ad a extra step to the reloading procedure, I readjusted my .45acp seater die with the RN plug to add a bit of a radius to the WC bullet nose, the leading problem went away
joneb is offline  
Old August 28, 2008, 09:30 AM   #6
crowbeaner
Senior Member
 
Join Date: June 4, 2007
Location: Upstate SC
Posts: 1,938
If you're using RCBS dies, the 38 set has a wadcutter seating stem in one set. I have 3 different seating stems in my box; RN, SWC, and WC. If you call RCBS they might even send you one for nada. I seat and crimp in seperate steps because the WCs are usually seated flush or just below the case mouth but you may be able to seat them down to the first crimp groove if they have one. I cast all mine, so YMMV. I use the Lee 38-148-wc and Lyman 35891.
__________________
If you want your children to follow in your footsteps, be careful where you walk.
Beware the man that only owns one gun; he probably knows how to use it.
I just hope my ship comes in before my dock rots.
crowbeaner is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07535 seconds with 7 queries