The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old June 11, 2008, 07:02 AM   #1
Jimyh159
Junior Member
 
Join Date: June 11, 2008
Posts: 1
Clogged barrel

?? I was recently handed a Traditions in-line rifle from a neighbor. He explained to me that he purchased the weapon to take up hunting last fall season. The gun is 9 years old, but was still in original box and unused he he aquired it. After firing the weapon a few times, it would not work properly. After a few questions, I realized that the gun he handed me still has a charge and sabot round in the barrel. Apparently the gun fouled and the charge never fired. I have attempted to push the charge and round out with the standard ram rod to no avail. How do I clear the weapon?? Is there a solvent that will break down the pyrodex charge so I can push the sabot free?
Jimyh159 is offline  
Old June 11, 2008, 09:56 AM   #2
Raider2000
Senior Member
 
Join Date: July 23, 2007
Location: Virginia
Posts: 717
Have you removed the breach plug & tried to simply push the bullet & charge out of the rear of the weapons breach?

Normally with an in line muzzleloader you take the breach plug out to clean it & this is the best way to remove any stuck loads in the weapon, maybe also to try using some WD40 or Balistol to try & lube it up to help in removal.
Raider2000 is offline  
Old June 11, 2008, 10:27 AM   #3
Pahoo
Senior Member
 
Join Date: February 16, 2006
Location: IOWA
Posts: 5,473
WOW

I am to understand that you have not attempted to shoot this in-line. Not sure which model you have but as Raider2000 stated, you should attempt to remove the breech plug, if indeed it has one. Some in-lines do not. The charge now in place should not give you a problem but the fouling from the previous discharges, will. Balistol is good or Kroil oil and even Hoppes #9 plus. Give it a good soaking for a minimum of two hours.

Now, if you don't have a removeable breech plug, again give it a good soaking down the bore and pull it with your screw jag. Sabots are fairly easy to pull or at least easier than patched round ball. The good soaking should will make the powder inert. Wish I had a dollar for every miss-fire I've had to pull.
If you got a manual with this kid, see what they recommend. Most will and some don't.

Be Safe
Pahoo is offline  
Old June 11, 2008, 06:40 PM   #4
JayC
Member
 
Join Date: June 16, 2007
Posts: 34
Have you seen this CO2 load discharger?

http://www.cabelas.com/cabelas/en/te...pod&id=0006480

Very handy for those times when someone forgets the powder charge or when a barrel gets so fouled that the patch, jag, and rod get stuck (I've seen both and the tool worked well both times).
JayC is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09038 seconds with 7 queries