The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old April 2, 2008, 07:36 AM   #1
Jack Reevez
Member
 
Join Date: April 2, 2008
Posts: 32
how to detect lead or copper, using solvent?

Hi . Can anyone tell me how to detect if my handgun bore had copper or lead in it after cleaning it with Hoppes #9 and Hoppes Elite Gun cleaner?

I shot a few rounds a few days back and cleaned my revolver with Hoppes Elite gun cleaner. The first patch cleaned the Powder fouling and the unburnt powder... i soaked the barrel with Elite Gun Cleaner over night and ran dry patches. They came out Dry. Shouln't there have been lead on the patches?
Jack Reevez is offline  
Old April 2, 2008, 05:16 PM   #2
Tempest45
Member
 
Join Date: July 17, 2007
Posts: 32
Copper will turn the appropriate solvent green or blue, depending on solvent type. The only true solvent for lead is mercury, which is very dangerous.

Hoppes elite solvent will attack neither. It is a degreaser and carbon solvent. It is also water based so be careful about leaving it on the gun for too long. Hoppes 9 is a miled copper solvent, and might have a slight lead lifting affect.

Did you shoot lead or jacketed bullets?
Tempest45 is offline  
Old April 3, 2008, 12:19 AM   #3
Jack Reevez
Member
 
Join Date: April 2, 2008
Posts: 32
Tempest45

i Only shoot lead bulletts. i got them with the guns... around 300 of them i think.
I also have many diff cleaners. Heres what i use..

1. Hoppes # 9 to remove lead from pistols.
2. Hoppes Elite gun cleaner to remove Lead from pistols ( since u said it doesnt attack lead i tyhink i'll just use to to remove carbon now and then #9 for lead)
3. Hoppes Bench rest #9 ( i ius eit to remove plastic from my shotguns)

i have ordered some Clenzoil field & range Solution , Prolix Lubricant ( CLP)and The Blue wonder gun cleaner. I havent got them yet.

Do u think i am using the right solvents for the right reasons?
Jack Reevez is offline  
Old April 3, 2008, 12:23 AM   #4
Jack Reevez
Member
 
Join Date: April 2, 2008
Posts: 32
Tempest45

u say Hoppes elite gun cleaner is a degreaser not a solvent...
what is a degreaser and how and when should it be used?

Should i use it to first remove carbon from the barrel of my handguns and then use other solvents to remove lead and then another solvent to remove copper and then oil it and store it?

Whats the need for a degreaser?
Jack Reevez is offline  
Old April 3, 2008, 07:47 AM   #5
DBotkin
Senior Member
 
Join Date: December 14, 2006
Location: Omaha, NE
Posts: 302
If you have leading in the barrel, chances are you'll be able to see it. If you're really worried about it, drag a Lewis Lead Remover (or the other brands of similar devices) through the barrel. They use a brass screen around a rubber or aluminum plug to scrape the lead out, they're quite effective.
DBotkin is offline  
Old April 4, 2008, 04:18 PM   #6
Tempest45
Member
 
Join Date: July 17, 2007
Posts: 32
Quote:
Whats the need for a degreaser?
Degreasers usually attack organic compounds. Oil, grease, carbon, etc. There are many different types. Strong solvents, soaps, etc. They are used to get the metal as clean as possible. You have to be careful because they also strip away protective lubricant that prevents rust.

They will not attack baked on copper or lead as these materials are not organic. I use Weapon Shield as an overall CLP. It is the best that I have seen and cleans better than most dedicated cleaners, especially after a cleaning or 2, all without strong solvents. The products you mentioned should also be fine, but are not my favorites.

If you have heavy leading the Lewis remover or a lot of brush work is about the only way to get it out. Letting the barrel soak in an oil for a few days first may help to lift the lead off the metal by mechanical action.
Tempest45 is offline  
Old April 4, 2008, 05:30 PM   #7
W. C. Quantrill
Senior Member
 
Join Date: February 11, 2008
Location: No Man's Land
Posts: 353
Leading is caused by hot loads and hard cast bullets. If you will use softer alloys on loads under about 1400 fps, you will not have a problem with leading. Leading is usually caused when there is not enough chamber pressure present to bump up the bullet to barrel groove diameter, or the bullet is too hard to expand, and the hot powder gasses bypass the bullet melting some of it and soldering it onto the barrel. The soft bullets allow the bullet to obiturate to bore diameter and seal the hot gasses behind.

If you have a question, get a bronze brush of proper size and brush the barrel. If there is any lead, it will take it out. The bronze brush will not harm your steel barrel.
__________________
NRA Life
Whittington Center Life
W. C. Quantrill is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:22 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07453 seconds with 7 queries