The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools
Old March 17, 2008, 04:14 PM   #1
jtrent211
Junior Member
 
Join Date: February 18, 2008
Posts: 8
Harrington & Richardson single barrel shotgun

First let me begin by saying I know VERY LITTLE about shotguns, never shot one, had no desire. Going thru some stuff of my Fathers found shotgun that I remember him saying it belonged to his Father. This I know Harrington & Richardson single 26" barrel, exposed hammer. no model #, stamped on side Feb.20-27 either 1899 or 1900 hard to tell both could be wrong. Serial # in 2 places 207030 that I've found. Problem is it is in two separate pieces, there is a missing part that holds the barrel into the stock, just guessing but looks like it would be a rod/lever device. Could anyone tell me what I'm looking for ANY help would be greatly appreciated. Thought I would clean-up this old gun, not to shoot and give to my Son, something from his Father,Grandfather, Great Grandfather. Thanks.
jtrent211 is offline  
Old March 17, 2008, 06:35 PM   #2
elrod
Senior Member
 
Join Date: May 19, 2007
Location: Heart of the heart of Dixie
Posts: 235
H&R began manfacture of single-shot, break-open shotguns in 1908. These were chambered in various guages and several barrel lengths and chokes. There is little collector interest in these guns.
These break down into three pieces rather easily. These are: Stock (the wooden part that fits against your shoulder while firing), Barrel (the long tube), and the forearm (wooden part that fits under barrel and is supported by non-firing hand).
Below are some links to parts suppliers with some exploded views;

http://www.gun-parts.com/harringtonrichardson/

http://www.e-gunparts.com/productsch...Model=1560z176

http://www.e-gunparts.com/productsch...odel=1560z188A

Hope that helps some


Al
__________________
Freedom ain't free!
elrod is offline  
Old March 18, 2008, 08:01 AM   #3
jtrent211
Junior Member
 
Join Date: February 18, 2008
Posts: 8
Thanks for the info. I now have a problem that I need the Harrington & Richardson Shotgun Model # before I can order parts. No model # on gun. Catch twenty-two situation. Is it even possible to obtain the model #? I have tried to no avail. Suggestions.
jtrent211 is offline  
Old March 18, 2008, 11:28 AM   #4
Steven Mace
Senior Member
 
Join Date: November 15, 1999
Location: Clifton, Colorado USA
Posts: 724
jtrent211, what are the markings on the barrel?

Steve Mace
__________________
After today, its all historical
Steven Mace is offline  
Old March 18, 2008, 12:39 PM   #5
jtrent211
Junior Member
 
Join Date: February 18, 2008
Posts: 8
nothing on barrel, but reads harrington & richardson arms co. worcester mass usa pat feb 20 & 27 1900 on the receiver behind the trigger guard. it also reads pat feb 20 & 27 1900, pat may 14 1901 on the receiver above the trigger guard. hope i have not confused you, thanks.
jtrent211 is offline  
Old December 5, 2010, 04:33 AM   #6
5thInfDivret
Junior Member
 
Join Date: December 5, 2010
Posts: 1
Guess I finally found someone w/a similar gun..Harrington & Richardson 12ga single shot shotgun, yep, may14th,but mine says 1901....still got it?? sfm
5thInfDivret is offline  
Old December 18, 2010, 09:34 PM   #7
TheKlawMan
Junior member
 
Join Date: June 23, 2009
Location: Orange County, CA
Posts: 2,149
I have one marked the same as jtrent's, but the markings may not be stamped in the same receiver locations. Serial no is 36616. The firing pin doesn't retract on its own but I have never fired or disassembled it.

On the left upper front of the receiver is stamped PAT FEB 20 & 27, 1900. Immediately beneth that it says PAT MAY 14, 1901. Then above the trigger guard is stamped HARRINGTON & RICHARDSON ARMS CO. Below this it reads "WORCESTER MASS USA PAT FEB 20 & 27, 1900."

Barrel measures 32".

Here is a link to a post on the characteristics of the model 1900 aand 1908. http://www.thefirearmsforum.com/showthread.php?t=55936

Last edited by TheKlawMan; December 18, 2010 at 10:12 PM. Reason: add link to info on models
TheKlawMan is offline  
Old December 23, 2010, 05:17 PM   #8
32 Magnum
Member In Memoriam
 
Join Date: January 17, 2009
Location: Eastern PA
Posts: 364
The easiest way to tell the difference in the earliest models - is the hinge pin.
Large frame 1900 and small frame 1905 - will have removable hinge pin.
Large frame 1908 and small frame 1915 - will have fixed hinge pin.
See pics attached:
IMG_2282_2.jpg

IMG_2315_2.jpg
32 Magnum is offline  
Old January 1, 2011, 11:35 AM   #9
32 Magnum
Member In Memoriam
 
Join Date: January 17, 2009
Location: Eastern PA
Posts: 364
The earliest H&R shotguns were the "Anson & Deeley" hammerless doubles of the early to mid 1880s. It is not known whether the parts were made in England and assembled here or made and assembled here, under license, or possibly a combination of both????? The next foray into shotgun making began in 1901 with the Model 1900 single shot, break action, heavy frame.

IMG_2213.jpg
32 Magnum is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:18 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08370 seconds with 8 queries