The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > NFA Guns and Gear

Reply
 
Thread Tools
Old January 12, 2008, 12:22 PM   #1
chaynes
Junior Member
 
Join Date: January 12, 2008
Posts: 3
M2 carbine parts and identification

First off, I just found this forum this morning and it rocks! I think it will be a great resource for the future. Also, this being my first post, admins feel free to re-post it in another section if 'NFA guns and gear' is not appropriate.

I have found an M1 carbine that I am interested in, but I have learned that it may come with some M2 carbine parts. I am nervous about this, since a fully auto M2 carbine is considered illegal. From reading these forums, I have discovered that there are 7 M2 parts needed for fully auto action. Does anyone have pictures of these parts that I can use to identify what parts are M2? I don't have any pics of the gun or I would post them up. I understand that it is not a full M2, but i would like to know what parts on it are.

Any help is appreciated!
chaynes is offline  
Old January 12, 2008, 02:55 PM   #2
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 16,841
The bolt was a round bolt. This was done to increase the mass and weight to slow down the rate of fire that would result with the original M-1 bolt. The bolt was interchanged freely with the M-1 so I wouldn't worry about it.

The magazine catch had a little finger that protruded out towards the muzzle. About 1/8" or 3/16" long, it was intended to stabilize the 30 round magazine designed for the M-2. That kinda became a standard part for the M-1 so don't worry about that either.

The M-2 Slide (operating rod) appeared much like the later M-1 Carbine slide. The difference was that a portion of the front was milled away to make space for the trip lever. Unknown if this can be used.

Hammer & Sear - both were cut differently. Unknown if these may be used.

Definitely keep the following out of your gun:

Trip lever - does not belong.
Selector switch - does not belong.
disconnector, disconnector spring and plunger - does not belong.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old January 12, 2008, 09:03 PM   #3
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,464
Many years ago, the (then) ATTD (now BATFE) listed the six parts they considered necessary to either convert an M1 carbine to selective fire or that in themselves constitute a machinegun within the meaning of the term in the National Firearms Act.

They are: 1) M2 hammer, 2) M2 sear, 3) disconnector, 4) disconnector lever, 5) selector, and 6) M2 slide (cut out on right side to operate the disconnector lever).

Note that the M2 trigger housing, M2 stock, round bolt, and small parts (springs) are NOT included.

The three parts that are exclusive to selective fire and have no place in a semi-auto are the disconnector, disconnector lever, and selector. The M2 hammer will work in an M1 with a shim. Many M1 carbines sold through DCM and CMP had or have M2 slides and M2 sears, as well as M2 trigger housings.

Note that ALL of those six parts are needed to convert an M1 carbine to selective fire. ALL, not just some. And you have to have ALL of them to constitute an "M2 kit" which is a machinegun in and by itself, whether you have an M1 carbine or not.

If your carbine doesn't have any of those three exclusive parts, don't worry about it.

Jim
__________________
Jim K
James K is offline  
Old January 13, 2008, 09:01 AM   #4
chaynes
Junior Member
 
Join Date: January 12, 2008
Posts: 3
Thank you for all your help. I am going to look at it today, so I will keep these things in mind.
chaynes is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:06 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07148 seconds with 7 queries