The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 1, 2007, 04:44 PM   #1
Lavid2002
Senior Member
 
Join Date: April 6, 2007
Posts: 2,568
A Few shotgun shell questions

Ive been looking around and adding up the price of reloading shotgun cartridges.
JUST the parts of the shotshell come out to about .456 a shell
Thats as cheap as i could find a 3" 12 ga assortment. I can but 12 Ga. 3" at the store now for 8.56 for 25 rd. Why spend 11.56 reloading them? Can I get this price down a bit? How?
So far im counting for
Powder 14.99-1 Lb.
Primer 5.99 100x
Hull 3" 5.99 100x
Wad 3" 13.99 100x new
#6 shot-steel (waterfowling)-20.99 for 10 Lb.
What do you think? I wont spend extra money to reload haha can I get them cheaper?

P.S. do shotgun shells have to be tumbled for there brass heads?
__________________
Math>Grammar
Lavid2002 is offline  
Old May 1, 2007, 07:35 PM   #2
Lavid2002
Senior Member
 
Join Date: April 6, 2007
Posts: 2,568
bump
__________________
Math>Grammar
Lavid2002 is offline  
Old May 1, 2007, 08:03 PM   #3
Randy_che
Member
 
Join Date: July 28, 2005
Location: Houston, Texas
Posts: 56
It's hard to beat a box of promo loads, but you should be able to beat $8.56 for 25 reloading. Are you sure the $8.56 is the same load you are considering making?

Your math comes out about right. Using those costs and some load assumptions, I get around 48 cents per round, which is about $12 per box.

Since I haven't bought shotshell components in years, I don't know if your prices are high. They seem a little high to me, but someone else will have to chime in.
Randy_che is offline  
Old May 1, 2007, 08:08 PM   #4
wolverine350
Senior Member
 
Join Date: November 27, 2006
Location: ponca city ok
Posts: 746
I pay 3.88 for game loads a box at walmart, 3" is not bad i can get the steel shot for about 10.00 a box
__________________
CVA Kodiak Magnum .50 cal
Marlin 981T 22LR Bolt Action
Remington 770 Bolt Action 270
Thompson Center Encore 243
wolverine350 is offline  
Old May 1, 2007, 09:36 PM   #5
Rimrod
Senior Member
 
Join Date: October 19, 2005
Location: Behind enemy lines
Posts: 1,309
Now your using your noggin. Shotshell reloading doesn't always save money since the price of shot went up years ago. It will depend on what you want to shoot and what is available at the stores. There used to be a setup advertised that allowed you to make your own shot but it wasn't around long in the ads.
Rimrod is offline  
Old May 1, 2007, 09:59 PM   #6
Lavid2002
Senior Member
 
Join Date: April 6, 2007
Posts: 2,568
They box im comparing ant the one im reloading are different...I just think if im working harder i should be SAVING money...not loosing it....anyone have some shell materials to save me some green? Brands to go with? But not compromising quality....I want what i get in the stores...for elss at home : D
__________________
Math>Grammar
Lavid2002 is offline  
Old May 1, 2007, 11:06 PM   #7
Don H
Senior Member
 
Join Date: May 8, 2000
Location: SLC,Utah
Posts: 2,705
One way for you to save money is to buy the components in bulk. An 8 lb. keg of powder is a whole bunch cheaper, per pound, than buying it by the 1-pound container (one place I checked, Hodgdon Clays in the 14-oz container was 90 cents an oz;in the 8 lb. keg, it's 75 cents an oz). Same goes for primers - buying 100 at a time is the most expensive way to buy them - compare the unit price of a 1,000-primer sleeve versus 100 (even cheaper if you but 5 or 10 thousand). I'll bet that the price per wad is a lot less if you buy them by the thousand than if you buy them by the hundred.
Don H is offline  
Old May 2, 2007, 08:22 AM   #8
lockedcj7
Senior Member
 
Join Date: February 15, 2007
Posts: 968
Looks like you are over-paying for components. I reload 12ga and 20ga and can usually get a AA quality shell for 3.50/box.

Buy primers by the 1000 and powder by the 8lb keg at a store or gunshow to avoid the hazmat fee and they'll average out much cheaper. Use Claybuster wads and buy them in lots of 500 or 1000. Pick up hulls at public ranges (if allowed) or dove fields and they're free. If you have to buy them, get them once-fired from E-bay in lots of 1000. I'm also using recycled shot which works great on clays and doves and is scads cheaper.

You won't save any money but you'll make better quality shells and have the satisfaction of doing so.
lockedcj7 is offline  
Old May 2, 2007, 12:10 PM   #9
snuffy
Senior Member
 
Join Date: May 20, 2001
Location: Oshkosh wi.
Posts: 2,774
Good gawd can't anybody read? He's talking about steel 3" waterfowl loads!

While I haven't bought any steel loads for 10 years or more,(I load my own), where do you find 3" steel loads for $8.56? See my answers on the loader post for where to get components.
__________________
The more people I meet, the more I love my dog

They're going to get their butts kicked over there this election. How come people can't spell and use words correctly?
snuffy is offline  
Old May 2, 2007, 03:56 PM   #10
Lavid2002
Senior Member
 
Join Date: April 6, 2007
Posts: 2,568
Can anyone else give me a setup...like a list of what to buy at the local stores? cheap good setup for shells? (not the rpesses i mean shotshell setup )
__________________
Math>Grammar
Lavid2002 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:23 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08810 seconds with 7 queries